Vmac G300003 Скачать руководство пользователя страница 60

Страница: 60 / 100

VMAC

– Vehicle Mounted Air Compressors

VMAC Technical Support:

1-888-241-2289

VMAC Knowledge Base: www.kb.vmacair.com

SYMPTOM

POSSIBLE CAUSE

CORRECTIVE ACTION

Engine rpm does not
decrease.

Throttle tube frozen,
plugged or obstructed.

Clean or replace tube.

Throttle actuator failure.

Replace actuator.

Discharge valve failure.

Replace discharge valve.

Using large receiver tank.

See p. 68.

Inlet regulator pressure
set below unloader valve
pressure setting.

Follow the inlet regulator
adjusting steps on p. 68.

SYMPTOM

POSSIBLE CAUSE

CORRECTIVE ACTION

Engine rpm does not
increase.

Unloader valve manually
activated.

Manually disengage unloader
valve.

Inlet valve regulator
pressure set too low.

Adjust inlet valve regulator to
increase pressure.

Discharge valve failure.

Replace discharge valve. .

Throttle actuator failure.

Replace actuator.

SYMPTOM

POSSIBLE CAUSE

CORRECTIVE ACTION

Blowdown does not
function.

Scavenge tube frozen,
plugged or obstructed.

Clean or replace tube.

Blowdown muffler
plugged or obstructed.

Replace muffler.

Blowdown valve failure.

Replace blowdown valve
assembly.

SYMPTOM

POSSIBLE CAUSE

CORRECTIVE ACTION

Oil comes out of the
blowdown muffler.

Operating angle more
than 15° from horizontal.

Reduce operating angle.

Compressor oil overfilled.

Check oil level with equipment on
level ground.

Faulty blowdown shuttle
valve.

Replace blowdown shuttle valve.

Blowdown valve failure.

Replace blowdown valve
assembly.

SYMPTOM

POSSIBLE CAUSE

CORRECTIVE ACTION

Engine overheat.

High ambient
temperatures.

Reduce duty cycle.

Low engine oil level.

Check engine oil level with
equipment on level ground.

Cooling intake plugged.

Correct problem.

Insufficient ventilation.

Correct problem.

Spark arrester fouled.

Clean spark arrester.

Mounted in enclosure.

See enclosure mounting
parameters on p. 21.

Содержание G300003





































































































Результаты поиска

Содержание G300003

Отзывы:

Бренды по названию

Популярные бренды

Vmac G300003, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание G300003

Отзывы:

Бренды по названию

Популярные бренды