Vmac G300003 страница 10 Скачать руководство пользователя

Страница: 10 / 100

VMAC

– Vehicle Mounted Air Compressors

VMAC Technical Support:

1-888-241-2289

VMAC Knowledge Base: www.kb.vmacair.com

General Warnings

•

Disconnect the spark plug wire before attempting any
repair or service.

•

Be attentive for unexplained changes in operation
parameters and record any changes.

•

Check the compressor oil level and condition before
starting the system. Do not add or change oil while the
system is running. Use only approved oil.

•

The compressor operates anytime the engine is
running. Avoid contact with the compressor, hoses, or
engine during operation.

•

Keep hoses and wiring away from hot, sharp, or
moving components.

•

Use only approved hoses and replacement parts.

•

Do not modify the equipment.

•

Do not operate the air compressor when fatigued or
under the influence of alcohol or drugs.

•

Know how to operate the compressor, fully read the
manual.

•

Check equipment before every use.

•

Never bypass or disable any of the safety equipment.

•

Never adjust or attempt to make any repairs to the
compressor system while the engine is running.
Components and hoses under pressure could fail and
cause serious injury or death.

Содержание G300003





































































































Результаты поиска

Содержание G300003

Отзывы:

Похожие инструкции для G300003

Бренды по названию

Популярные бренды

Vmac G300003, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание G300003

Отзывы:

Похожие инструкции для G300003

Бренды по названию

Популярные бренды