Vmac G300003 Скачать руководство пользователя

Страница: 12 / 100

VMAC

– Vehicle Mounted Air Compressors

VMAC Technical Support:

1-888-241-2289

VMAC Knowledge Base: www.kb.vmacair.com

Safety Features

Do not disable or bypass any safety components. Disabling
or bypassing safety components could result in equipment
damage, injury or death.

Read this manual in its entirety prior to operating or
performing any service or repairs to the Gas Engine Driven
30 CFM Air Compressor.

Gas Engine Driven 30 CFM Air Compressor
Safety Components

•

200 psi pressure relief valve in the separation manifold.

•

Blowdown muffler to discharge system pressure on shut down.

•

Temperature safety switch in compressor.

•

15 A fuse protects the OEM electrical system (located inside the
OEM key start enclosure).

•

15 A

fuse protects the fan’s electrical system (located in the wiring

harness next to the battery).

Figure 1

– Safety components (Shroud removed for clarity)

Automatic Overheat Shut down

If the compressor oil temperature exceeds 140 °C (284 °F), the thermostatic
switch will disable the engine. The cooling fan is powered by the battery and
will continue to run as needed to cool the compressor.

The engine will not be able to be restarted until the system has
cooled and the temperature switch has closed.

Temperature

switch

200 psi relief

valve

Blowdown

muffler

Содержание G300003





































































































Результаты поиска

Содержание G300003

Отзывы:

Похожие инструкции для G300003

Бренды по названию

Популярные бренды

Vmac G300003, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание G300003

Отзывы:

Похожие инструкции для G300003

Бренды по названию

Популярные бренды