Vmac G300003 страница 79 Скачать руководство пользователя | Manualshive

Страница: 79 / 100

background image

VMAC

– Vehicle Mounted Air Compressors

VMAC Technical Support:

1-888-241-2289

VMAC Knowledge Base: www.kb.vmacair.com

77

Inlet Valve Replacement

Read the

“Maintenance and Repair Safety” section prior to

performing any work on the system (beginning on Page 38).
Wear appropriate Personal Protective Equipment and follow
all industry standard safety practices.

The compressor inlet valve uses 2 different length bolts. The
longer bolts are 55 mm long and the shorter ones are 50 mm
long. Ensure the bolts are installed in the correct position.

Installing the inlet bolts in the wrong location could severely
damage the compressor (Figure 66).

Figure 66

– Inlet valve fasteners



Follow the instructions to remove the compressor (starting on page 74).



Place the compressor on a bench.



Remove the 4 socket head bolts securing the inlet valve to the
compressor.



Ensure the O-ring is not defective or damaged.

Loctite is not required on the inlet valve bolts.



Install the inlet valve in the reverse order.

Longer fasteners (2x)

Shorter fasteners (2x)

Viton O-ring

«
...
77
78
79
80
81
...
»

Содержание G300003





































































































Отзывы:

Нет отзывов

Похожие инструкции для G300003

Бренд: paasche Страницы: 2

IRONFORCFe WL6500 series

Бренд: Campbell Hausfeld Страницы: 24

Бренд: Koci Elektromaschinen Страницы: 15

Бренд: XTline Страницы: 28

Бренд: Will Burt Страницы: 8

Бренд: North American Tool Страницы: 10

Бренд: Atlas Copco Страницы: 103

PTS 1600 Cud S3A/T3 APP

Бренд: Atlas Copco Страницы: 128

Бренд: Atlas Copco Страницы: 128

Бренд: Atlas Copco Страницы: 150

Бренд: Atlas Copco Страницы: 152

Бренд: Nibe Страницы: 8

Dynamite Power Air Compressor

Бренд: Wagan Страницы: 7

M135 SIGMA CONTROL MOBIL

Бренд: KAESER Страницы: 288

Powerplus POWX1705

Бренд: VARO Страницы: 9

Бренд: Ingersoll-Rand Страницы: 44

Бренд: Ingersoll-Rand Страницы: 57

Бренд: Ingersoll-Rand Страницы: 98

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды