background image

 

 

57

6.3.2  Faults 

 

The  faults  are  displayed  by  flickering  display  of  QAA  88  device.  Current  fault  number  is  displayed  in  P  15 
parameter. In case more faults occur simultaneously first of all the fault with higher number will be displayed.  

The  non-reversible  fault  4  must  be  quitted  after  its  elimination  which  is  done  on  the  introductory  display  of 
QAA  device  (i.e.  leave  P  15  parameter  of  the  device  up  to  the  introductory  display)  by  the  simultaneous 
pressing  of  keys  (+arrow  up,-  arrow  down)  for the period of approx. 3 sec. Display flickering will disappear. 
The reversible faults disappear automatically after their elimination.  

In  case  of  fault  10  -  of  heating  branch  sensor  (only  in  case  of  mixing  heating  circuit)  the  three-way  mixing 
valve  closes. As the temporary variant (before we replace the sensor) we can select the boiler operation at 
the fixed temperature (P 24 parameter) plus the heating branch three-way mixing valve switch-over to MAN 
position. We select setting of heating branch three-way mixing valve manually. After the fault elimination we 
again  select  the  automatic  boiler  operation  and  we  switch  over  the  three-way  mixing  valve  back  to  AUTO 
position. Until the heating branch sensor is replaced the fault is signalled on QAA 88 device. 

In case of fault 1 i.e. exceeding of max. boiler temperature the boiler might be shut down through the safety 
thermostat  set  to  approx.  100  °C.  This  fault  is  non-reversible  and  it  is  necessary  to  de-block  the  safety 
thermostat after the boiler has cooled down. The de-blocking button is found under the black plastic cover. 

 

Tab. no. 8  Faults  

Image 

Sensor 

Fault description  

Boiler response 

B2 

Exceeding of safety temperature  
(max. boiler value) 

Boiler shut-down. The pumps are still 
working. The three-way valve opens and 
water is withdrawn into the heating 
system. 

B5 

Exceeding of fuel feeder temperature 

Fuel feed according to the set algorithm 
so that the burning fuel is returned into 
the burner. 

Motor 

heating 

protection 

Exceeding of fuel feeder motor winding 
temperature  

Boiler shut-down. The primary pump is 
still working. After the winding has cooled 
down and the heating protection has re-
switched put the boiler into operation. 

B2 

Extinction of boiler. The outlet 
temperature in a given time interval does 
not grow. The absence of fuel, feeder 
blockage etc. might be the reasons. 

Boiler shut-down. The protection against 
fuel fire penetration is active 
 

B3 

Overheating of warm water in HW 
reservoir  

End of HW heating. Three-way valve 
turns to HC. 

B1 

HC overheating 

HC heating and HC pump shut-down. 

Time validity. 
If absence of voltage on regulator is 
longer than approx. 3 days counting of 
time (date, time) will stop. It is necessary 
to set current time a date. 

Boiler heats to the set temperature in the 
first period on Monday. 

 

Содержание EKORET SAPHIR 15





































































Отзывы: