VESPA GTS Super 300 ie 2008 Скачать руководство пользователя

Страница: 203 / 317

With injector disconnected and the injector load

relay disconnected, check the continuity of the

Black-Green cable between the injector connector

and solenoid base.

Inspecting the injector hydraulics

To carry out the injector check, remove the intake

manifold by removing the three clamping screws

at the head and the clip connecting the control unit

to the manifold.

Install the appropriate tool for checking fuel pres-

sure and position the manifold over a container

graduated by at least 100 cm³. Connect the injec-

tor with the cable making up part of the supply for

the injection tester. Connect the clamps of the ca-

ble to an auxiliary battery. Activate the fuel pump

with the active diagnosis. Check that, within fifteen

seconds, approximately 40 cm³ of fuel is dis-

pensed with an adjustment pressure of approxi-

mately 2.5 BAR.

Specific tooling

020480Y

Petrol pressure check kit

Vespa GTS Super 300 ie (2008)

Injection

INJEC - 203

Содержание GTS Super 300 ie 2008






























































































































































































































































































































Результаты поиска

Содержание GTS Super 300 ie 2008

Отзывы:

Похожие инструкции для GTS Super 300 ie 2008

Бренды по названию

Популярные бренды

VESPA GTS Super 300 ie 2008, Руководство по обслуживанию станции

Результаты поиска

Содержание GTS Super 300 ie 2008

Отзывы:

Похожие инструкции для GTS Super 300 ie 2008

Бренды по названию

Популярные бренды