VESPA GTS Super 300 ie 2008 Скачать руководство пользователя страница 164

Страница: 164 / 317

Crankcase - crankshaft

Splitting the crankcase halves

- Before opening the crankcase, it is advisable to

check the axial clearance of the crankshaft. To do

this, use a plate and a support with appropriate tool

dial gauge.

- Upper clearances are an indication of wear on

the surfaces of the crankshaft casing support.

- Remove the 10 crankshaft coupling screws.

- Separate the crankcase while keeping the crank-

shaft in one of the two halves of the crankcase.

- Remove the crankshaft.

- Remove the half crankcase coupling gasket.

- Remove the two screws and the internal cover

shown in the diagram.

- Remove the oil guard on the flywheel side.

- Remove the oil filter fitting shown in the diagram.

- Check the axial clearance on the connecting rod.

- Check the radial clearance on the connecting rod.

-Check the surfaces that limit the axial free-play

are not scored and measure the width of the crank-

shaft between these surfaces, as shown in the

diagram.

- If the axial clearance between crankshaft and

crankcase is exceeding and the crankshaft does

not have any defect, the problem must be due to

either excessive wear or wrong machining on the

crankcase.

- Check the diameters of both the bearings of the

crankshaft in accordance with the axes and surfa-

ces shown in the figure. The half-shafts are clas-

sified in two categories Cat. 1 and Cat. 2 as shown

the chart below.

CAUTION

THE CRANKSHAFT CAN BE REUSED WHEN THE WIDTH
IS WITHIN THE STANDARD VALUES AND THE SURFACES
SHOW NO SIGNS OF SCORING.

Engine

Vespa GTS Super 300 ie (2008)

ENG - 164

Содержание GTS Super 300 ie 2008






























































































































































































































































































































Результаты поиска

Содержание GTS Super 300 ie 2008

Отзывы:

Похожие инструкции для GTS Super 300 ie 2008

Бренды по названию

Популярные бренды

VESPA GTS Super 300 ie 2008, Руководство по обслуживанию станции

Результаты поиска

Содержание GTS Super 300 ie 2008

Отзывы:

Похожие инструкции для GTS Super 300 ie 2008

Бренды по названию

Популярные бренды