VESPA GTS Super 300 ie 2008 Скачать руководство пользователя страница 208

Страница: 208 / 317

9. Fuel injector

10.Electric fan solenoid

The ignition system is integrated with the injection and it is a high-efficiency inductive type ignition.

The control unit manages two significant parameters:

- Ignition advance

This is optimised at once according to the engine revs, engine load, temperature and ambient pressure.

With idle engine, it is optimised to obtain the stabilisation of the speed at 1450 ± 50 R/1'.

- Magnetisation time

The coil magnetisation time is controlled by the control unit. The ignition power is increased during the

engine start-up phase.

The injection system recognises the four-stroke cycle so the ignition is only commanded in the com-

pression phase.

Specific tooling

020331Y

Digital multimeter

Check that the injection load 15A fuse No. 2 works

properly.

Check that the 7.5A fuse No. 5 for live control unit

power works properly.

Check the efficiency of the injection load solenoid.

Check the resistance of the energising coil be-

tween pins 86 and 85: 40 to 80 Ohm

Apply a voltage of 12V to pins 86 and 85; make

sure that there is continuity between pins 30 and

87 of the relay.

Injection

Vespa GTS Super 300 ie (2008)

INJEC - 208

Содержание GTS Super 300 ie 2008






























































































































































































































































































































Результаты поиска

Содержание GTS Super 300 ie 2008

Отзывы:

Похожие инструкции для GTS Super 300 ie 2008

Бренды по названию

Популярные бренды

VESPA GTS Super 300 ie 2008, Руководство по обслуживанию станции

Результаты поиска

Содержание GTS Super 300 ie 2008

Отзывы:

Похожие инструкции для GTS Super 300 ie 2008

Бренды по названию

Популярные бренды