VESPA GTS Super 300 ie 2008 Скачать руководство пользователя страница 174

Страница: 174 / 317

Removal

- Undo the two clamping screws in the figure and

remove the cover over the pump control sprocket.

- Block the rotation of the oil pump control pulley

with a screwdriver inserted through one of its two

holes.

- Remove the central screw with Belleville washer,

as shown in the diagram.

- Remove the chain with the crown.

- Remove the control sprocket wheel with relative

O-ring.

- Remove the oil pump by undoing the two screws

in the figure.

- Remove the oil pump seal.

N.B.

IT IS ADVISABLE TO MARK THE CHAIN IN ORDER TO EN-
SURE THAT THE INITIAL DIRECTION OF ROTATION IS
MAINTAINED.

Inspection

- Remove the two screws and the oil pump cover.

- Remove the circlip retaining the innermost rotor.

- Remove and wash the rotors thoroughly with pet-

rol and compressed air.

- Reassemble the rotors in the pump body, keep-

ing the two reference marks visible Replace the

retainer ring.

Engine

Vespa GTS Super 300 ie (2008)

ENG - 174

Содержание GTS Super 300 ie 2008






























































































































































































































































































































Результаты поиска

Содержание GTS Super 300 ie 2008

Отзывы:

Похожие инструкции для GTS Super 300 ie 2008

Бренды по названию

Популярные бренды

VESPA GTS Super 300 ie 2008, Руководство по обслуживанию станции

Результаты поиска

Содержание GTS Super 300 ie 2008

Отзывы:

Похожие инструкции для GTS Super 300 ie 2008

Бренды по названию

Популярные бренды