VESPA GTS Super 300 ie 2008 Скачать руководство пользователя страница 134

Страница: 134 / 317

- Lock the driven pulley again using the specific

tool.

- Preload the clutch return spring with a traction/

rotation combined action and place the belt in the

smaller diameter rolling position.

- Remove the driven pulley /belt unit from the tool.

N.B.

DURING THE SPRING PRELOADING PHASE, BE CARE-
FUL NOT TO DAMAGE THE PLASTIC SPRING STOP AND
THE BUSHING THREADING.

N.B.

FOR DESIGN REASONS, THE NUT IS SLIGHTLY ASYM-
METRIC; THE FLATTEST SURFACE SHOULD BE MOUN-
TED IN CONTACT WITH THE CLUTCH.

Specific tooling

020444Y

Tool for fitting/ removing the driven

pulley clutch

020444Y011

adapter ring

020444Y009

wrench 46 x 55

Locking torques (N*m)

Clutch unit nut on driven pulley

45 ÷ 50

Refitting the driven pulley

- Refit the clutch bell.

Engine

Vespa GTS Super 300 ie (2008)

ENG - 134

Содержание GTS Super 300 ie 2008






























































































































































































































































































































Результаты поиска

Содержание GTS Super 300 ie 2008

Отзывы:

Похожие инструкции для GTS Super 300 ie 2008

Бренды по названию

Популярные бренды

VESPA GTS Super 300 ie 2008, Руководство по обслуживанию станции

Результаты поиска

Содержание GTS Super 300 ie 2008

Отзывы:

Похожие инструкции для GTS Super 300 ie 2008

Бренды по названию

Популярные бренды