VESPA GTS Super 300 ie 2008 Скачать руководство пользователя страница 87

Страница: 87 / 317

Remove the protective base from the connector.

With the ignition switch at ON check there is bat-

tery voltage between the Red-White and Black

cables

Virgin circuit

When the ignition system is not encrypted, any key

will start the engine but limited to 2000 rpm. The

keys can only be recognised if the control unit has

been programmed properly.

The data storage procedure for a previously un-

programmed control unit provides for the recogni-

tion of the red key (master key) as the first key to

be stored to memory: this becomes particularly

important because it is the only key that enables

the control unit to be wiped clean and reprogram-

med for the memorisation of the service keys.

The master and service keys must be used to code

the system as follows:

- Insert the Master key, turn it to «ON» and keep

this position for two seconds (lower and upper lim-

its 1 to 3 seconds).

- Insert the blue key and set to «ON» for 2 seconds.

- If you have copies of the key, repeat the operation

with each key.

Vespa GTS Super 300 ie (2008)

Electrical system

ELE SYS - 87

Содержание GTS Super 300 ie 2008






























































































































































































































































































































Результаты поиска

Содержание GTS Super 300 ie 2008

Отзывы:

Похожие инструкции для GTS Super 300 ie 2008

Бренды по названию

Популярные бренды

VESPA GTS Super 300 ie 2008, Руководство по обслуживанию станции

Результаты поиска

Содержание GTS Super 300 ie 2008

Отзывы:

Похожие инструкции для GTS Super 300 ie 2008

Бренды по названию

Популярные бренды