VESPA GTS Super 300 ie 2008 Скачать руководство пользователя

Страница: 154 / 317

Removing the valves

- Using the appropriate tool fitted with an adaptor,

remove the cotters, caps, springs and valves.

- Remove the oil guards with the appropriate tool.

- Remove the lower spring supports.

CAUTION

REPLACE THE VALVES IN SUCH A WAY AS TO RECOG-
NISE THEIR ORIGINAL POSITION ON THE HEAD.

Specific tooling

020382Y011

adapter for valve removal tool

020382Y

Valve cotters equipped with part 012

removal tool

020431Y

Valve oil seal extractor

Removing the cylinder - piston assy.

Removing cylinder and piston

- Remove the chain guide slider.

- Remove the 4 O-rings on the stud bolts.

- Pull out the cylinder.

- Remove the cylinder base gasket.

- Remove the two stop rings, the wrist pin and the

piston.

- Remove the piston seals.

CAUTION

TO AVOID DAMAGING THE PISTON, SUPPORT IT WHILE
REMOVING THE CYLINDER.

N.B.

BE CAREFUL NOT TO DAMAGE THE SEALING RINGS
DURING REMOVAL.

Engine

Vespa GTS Super 300 ie (2008)

ENG - 154

Содержание GTS Super 300 ie 2008






























































































































































































































































































































Результаты поиска

Содержание GTS Super 300 ie 2008

Отзывы:

Похожие инструкции для GTS Super 300 ie 2008

Бренды по названию

Популярные бренды

VESPA GTS Super 300 ie 2008, Руководство по обслуживанию станции

Результаты поиска

Содержание GTS Super 300 ie 2008

Отзывы:

Похожие инструкции для GTS Super 300 ie 2008

Бренды по названию

Популярные бренды