VESPA GTS Super 300 ie 2008 Скачать руководство пользователя страница 137

Страница: 137 / 317

movable driving half-pulley bushing: Maxi-
mum allowable diameter

Ø 26.12 mm

Sliding bushing: Standard Diameter

Ø 25.959 ÷ 25.98 mm

Sliding bushing: Minimum admissible diame-
ter

Ø 25.95 mm

Roller: Standard Diameter

Diameter 20.5 - 20.7 mm

Roller: Minimum diameter permitted

Ø 20 mm

Refitting the driving pulley

- Preassemble the movable half-pulley with the

roller contrast plate by putting the rollers in their

housings with the larger support surface touching

the pulley according to the direction of rotation.

- Check that the roller contact plate does not have

flaws and is not damaged on the grooved edge.

- Mount the complete bushing unit on the crank-

shaft.

- Fit the driven pulley/Clutch/belt unit on the en-

gine.

Vespa GTS Super 300 ie (2008)

Engine

ENG - 137

Содержание GTS Super 300 ie 2008






























































































































































































































































































































Результаты поиска

Содержание GTS Super 300 ie 2008

Отзывы:

Похожие инструкции для GTS Super 300 ie 2008

Бренды по названию

Популярные бренды

VESPA GTS Super 300 ie 2008, Руководство по обслуживанию станции

Результаты поиска

Содержание GTS Super 300 ie 2008

Отзывы:

Похожие инструкции для GTS Super 300 ie 2008

Бренды по названию

Популярные бренды