VESPA GTS Super 300 ie 2008 Скачать руководство пользователя

Страница: 136 / 317

- Insert the tool in the hollows and apply the reten-

tion ring

- Bring in the ring's clamping screws while keeping

the tool to support the pulley

Specific tooling

020626Y

Driving pulley lock wrench

- Remove the fixing nut and the washer

- Remove the stationary drive pulley half.

Inspecting the rollers case

- Check that the internal bushing shown in the fig-

ure is not abnormally worn and measure inner

diameter A.

- Measure outer diameter B of the pulley sliding

bushing shown in the figure.

- Check that the rollers are not damaged or worn.

- Check the guide shoes for the variator back-plate

are not worn.

- Check the wear of the roller housings and of the

belt faying surfaces on both pulley halves.

- Check that stationary driving pulley does not

show signs of abnormal wear on the grooved edge

and on the surface in contact with the belt.

- Check that the O-ring is not pushed out of shape.

CAUTION

DO NOT LUBRICATE OR CLEAN SINTERED BUSHINGS

Characteristic

movable driving half-pulley bushing: Standard
Diameter

26.000 - 26.021 mm

Engine

Vespa GTS Super 300 ie (2008)

ENG - 136

Содержание GTS Super 300 ie 2008






























































































































































































































































































































Результаты поиска

Содержание GTS Super 300 ie 2008

Отзывы:

Похожие инструкции для GTS Super 300 ie 2008

Бренды по названию

Популярные бренды

VESPA GTS Super 300 ie 2008, Руководство по обслуживанию станции

Результаты поиска

Содержание GTS Super 300 ie 2008

Отзывы:

Похожие инструкции для GTS Super 300 ie 2008

Бренды по названию

Популярные бренды