VESPA GTS Super 300 ie 2008 Скачать руководство пользователя страница 210

Страница: 210 / 317

Check the presence of fixed voltage between the

grey/black cable of the remote control base and

earth. If there is none check the continuity of the

grey/black cable between the fuse box (No. 2 15

A) and the remote control base.

N.B.

CONTINUITY TESTS MUST BE CARRIED OUT WITH THE
COMPONENTS DISCONNECTED. (RELAYS, CONTROL
UNIT, FUSES ETC.).

Zeroing the throttle

Resetting the throttle valve position signal (TPS reset)

The MIU control unit is supplied with a throttle valve position sensor that is pre-calibrated.

Pre-calibration entails regulating the minimum opening of the throttle valve to obtain a certain flow of

air under pre-set reference conditions.

Pre-calibration ensures optimal air flow to control idling.

This regulation must not be tampered with in any way whatsoever.

The injection system will complete the management of the idling through the Stepper motor and the

variation of the ignition advance.

The throttle body after the pre-calibration has an opened valve with an angle that can vary depending

on the tolerances of the machining of the pipe and the valve itself.

The valve position sensor can also assume various fitting positions. For these reasons the mV of the

sensor with the valve at idle can vary from one throttle body to another.

Injection

Vespa GTS Super 300 ie (2008)

INJEC - 210

Содержание GTS Super 300 ie 2008






























































































































































































































































































































Результаты поиска

Содержание GTS Super 300 ie 2008

Отзывы:

Похожие инструкции для GTS Super 300 ie 2008

Бренды по названию

Популярные бренды

VESPA GTS Super 300 ie 2008, Руководство по обслуживанию станции

Результаты поиска

Содержание GTS Super 300 ie 2008

Отзывы:

Похожие инструкции для GTS Super 300 ie 2008

Бренды по названию

Популярные бренды