VESPA GTS Super 300 ie 2008 Скачать руководство пользователя

Страница: 181 / 317

- Spark plug

The MIU control unit manages ignition with the best advance ensuring four-stroke timing (ignition only

in the compression phase) at the same time.

The MIU injection-ignition system controls engine functions by means of a pre-set program.

Should any input signals fail, an acceptable working order of the engine is ensured to allow the user to

reach a service station.

Of course, this cannot happen when the rpm-timing signal is missing, or when the failure involves the

control circuits:

- Fuel pump

- HV coil

- Injector

The control unit is provided with a self-diagnosis

system connected to an indicator light in the in-

strument panel.

Failures are detected and restored by the diagnostic tester.

In any case, when the fault is no longer present, the data storage is automatically cleared after 16 cycles

of use (cold start, running at regular engine temperature, stop).

The diagnostic tester is also required to adjust the idle mixture.

Specific tooling

020922Y

Diagnosis Tool

The MIU injection-ignition system carries out

checks on the rpm indicator and the electric fan for

radiator cooling.

The MIU control unit has a decoder for the anti-

theft immobilizer system.

The MIU control unit is connected to a diagnostic

LED on the instrument panel, that also carries out

the deterrent flashing functions.

The MIU control unit power supply is furthermore controlled by the emergency switch; to allow further

safety of the vehicle.

Vespa GTS Super 300 ie (2008)

Injection

INJEC - 181

Содержание GTS Super 300 ie 2008






























































































































































































































































































































Результаты поиска

Содержание GTS Super 300 ie 2008

Отзывы:

Похожие инструкции для GTS Super 300 ie 2008

Бренды по названию

Популярные бренды

VESPA GTS Super 300 ie 2008, Руководство по обслуживанию станции

Результаты поиска

Содержание GTS Super 300 ie 2008

Отзывы:

Похожие инструкции для GTS Super 300 ie 2008

Бренды по названию

Популярные бренды