VESPA GTS Super 300 ie 2008 Скачать руководство пользователя страница 85

Страница: 85 / 317

25. H.V. coil.

26. Fuel injector

27. Engine temperature sensor

28. Fuel pump

30. Injection electronic control unit

31. Immobilizer antenna

34. Instrument panel

Checks and inspections

This section is dedicated to the checks on the electrical system components.

Immobiliser

The electronic ignition system is controlled by the

control unit with the integrated Immobilizer sys-

tem. The immobiliser is an antitheft system which

allows the vehicle to function only if it is activated

by means of the coded keys that the control unit

recognises. The code is integrated in a transpond-

er in the key block. This allows the driver clear

operation without having to do anything other than

just turning the key. The Immobilizer system con-

sists of the following components:

- Control unit

- Immobilizer aerial

- master and service keys with built-in transponder

- HV coil.

- diagnosis LED

The diagnosis LED also works as a theft-deterrent

blinker. This function is activated every time the

ignition switch is turned to the "OFF" position, or

the emergency stop switch is turned to the "OFF"

position. It remains activated for 48 hours in order

not to affect the battery charge.

When the ignition switch is turned to "ON", it inter-

rupts the function of the immobiliser lamp and a

start enable lamp comes "ON".

Vespa GTS Super 300 ie (2008)

Electrical system

ELE SYS - 85

Содержание GTS Super 300 ie 2008






























































































































































































































































































































Результаты поиска

Содержание GTS Super 300 ie 2008

Отзывы:

Похожие инструкции для GTS Super 300 ie 2008

Бренды по названию

Популярные бренды

VESPA GTS Super 300 ie 2008, Руководство по обслуживанию станции

Результаты поиска

Содержание GTS Super 300 ie 2008

Отзывы:

Похожие инструкции для GTS Super 300 ie 2008

Бренды по названию

Популярные бренды