VESPA GTS Super 300 ie 2008 Скачать руководство пользователя страница 223

Страница: 223 / 317

- Refit the fifth wheel fitting and the dust gaiter on

the steering bearing until they stop, using the spe-

cific tool.

Specific tooling

006029Y

Punch for fitting steering bearing seat

on steering tube

- Use the specific tool to fit the fifth wheel fitting on

the headstock as indicated in the figure

Specific tooling

001330Y

Tool for fitting steering seats

- Remove the steering tube

- Remove the attachment bracket

- Use the specific tool with the part 1 and operate

the handgrip until removing temporarily the pin and

the Nadella opposite the tool thrusting direction.

- To extract the second Nadella, use the tool with

the part 2, instead of part 1, on opposite side to the

one indicated in the figure.

Specific tooling

020021Y

Front suspension service tool

- Fit both dust guard rings

«C»

on the swinging hub

as shown in the detail drawing

«A»

- Connect the swinging hub to the steering tube

with the guiding pin, part 5.

- Use the specific tool fitted with part 3 on the stem

and part 4 on the tool base.

- Lubricate the pin with recommended grease and

insert it temporarily on the swinging hub, move the

tool handgrip until part 3 is fully inserted on the

steering tube.

Vespa GTS Super 300 ie (2008)

Suspensions

SUSP - 223

Содержание GTS Super 300 ie 2008






























































































































































































































































































































Результаты поиска

Содержание GTS Super 300 ie 2008

Отзывы:

Похожие инструкции для GTS Super 300 ie 2008

Бренды по названию

Популярные бренды

VESPA GTS Super 300 ie 2008, Руководство по обслуживанию станции

Результаты поиска

Содержание GTS Super 300 ie 2008

Отзывы:

Похожие инструкции для GTS Super 300 ie 2008

Бренды по названию

Популярные бренды