background image

DVB Series Direct Vent Gas Fireplace

20306740

3

IMPORTANT SAFETY INFORMATION

INSTALLER

Please leave these instructions with the appliance.

OWNER

Please retain these instructions for future reference.

This fireplace is a vented product. This fireplace must be 

properly installed by a qualified service person. The glass 

door must be properly seated and sealed. If this unit is not 

properly installed by a qualified service person with glass 

door properly seated and sealed, combustion leakage 

can occur.

 

CARBON MONOXIDE POISONING:

 Early signs of carbon 

monoxide poisoning are similar to the flu with headaches, 

dizziness and/or nausea. If you have these signs, the fire-

place may not have been installed properly. Get fresh air 

at once! Have the fireplace inspected and serviced by a 

qualified service person. Some people are more affected 

by carbon monoxide than others. These include pregnant 

women, people with heart or lung disease or anemia, those 

under the influence of alcohol, and those at high altitudes. 
Propane/LP gas and natural gas are both odorless. An 

odor-making agent is added to each of these gases. The 

odor helps you detect a gas leak. However, the odor added 

to these gases can fade. Gas may be present even though 

no odor exists.
Make certain you read and understand all warnings. Keep 

this manual for reference. It is your guide to safe and proper 

operation of this fireplace.
1.  This appliance is only for use with the type of gas 

indicated on the rating plate. This appliance is not 

convertible for use with other gases unless a certified 

kit is used. 

2.  For  propane/LP  fireplace,  do  not  place  propane/LP 

supply tank(s) inside any structure. Locate propane/

LP supply tank(s) outdoors. To prevent performance 

problems, do not use propane/LP fuel tank of less than 

100 lbs. capacity. 

3.  If you smell gas

• 

shut off gas supply.

• 

do not try to light any appliance.

• 

do not touch any electrical switch; do not use any 

phone in your building.

• 

immediately call your gas supplier from a neighbor’s 

phone. Follow the gas supplier’s instructions.

4.   Never install the fireplace 

  in a recreational vehicle

  where curtains, furniture, clothing, or other flam-

mable objects are less than 42" from the front, top, 

or sides of the fireplace

  in high traffic areas

  in windy or drafty areas 

5.  This fireplace reaches high temperatures. Keep children 

and adults away from hot surfaces to avoid burns or 

clothing ignition. Fireplace will remain hot for a time 

after shutdown. Allow surfaces to cool before touching. 

6.  Young children should be carefully supervised when 

they are in the same room as the appliance. Toddlers, 

young children and others may be susceptible to 

accidental contact burns. A physical barrier is recom-

mended if there are at risk individuals in the house. To 

restrict access to a fireplace or stove, install an adjust-

able safety gate to keep toddlers, young children and 

other at risk individuals out of the room and away from 

hot surfaces. 

7.  Do not modify fireplace under any circumstances. Any 

parts removed for servicing must be replaced prior to 

operating fireplace. 

8.  Turn fireplace off and let cool before servicing, installing, 

or  repairing.  Only  a  qualified  service  person  should 

install,  service,  or  repair  the  fireplace.  Have  burner 

system inspected annually by a qualified service person. 

9.  You must keep control compartments, burners, and 

circulating air passages clean. More frequent cleaning 

may be needed due to excessive lint and dust. Turn off 

the gas valve and pilot light before cleaning fireplace. 

10. Have venting system inspected annually by a qualified 

service person. If needed, have venting system cleaned 

or repaired. Refer to 

Cleaning and Maintenance

, Page 43. 

11.  Keep the area around your fireplace clear of combus-

tible materials, gasoline, and other flammable vapor 

and liquids. Do not run fireplace where these are used 

or stored. Do not place items such as clothing or dec-

orations on or around fireplace. 

• 

Read this owner’s manual carefully and completely before trying to assemble, operate, or service 

this fireplace. 

• 

Any change to this fireplace or its controls can be dangerous.

• 

Improper installation or use of this fireplace can cause serious injury or death from fire, burns, 

explosions, electrical shock and carbon monoxide poisoning.

W

ARNING

Содержание 300DVB(N/P)(V/SC)7SB













































































Отзывы: