Varec 7532 Скачать руководство пользователя страница 43

Страница: 43 / 106

7532

Operation

5.5.3

Commuwin II-Operating Program

Commuwin II is an operating software with graphical support for intelligent transmitters

with the communication protocols Rackbus, Rackbus RS 485, INTENSOR, HART or

PROFIBUS-PA. It is compatible with the operating systems Win 3.1/3.11, Win95, Win98

and WinNT4.0. All functions of Commuwin II are supported. The configuration is made

via operating matrix or graphic surface. A envelope curve can be displayed in ToF Tool.

Note!

Further information on Commuwin II is given in the following Varec documentation:
• System Information: SI 018F/00/en “Commuwin II”
• Operating Manual: BA 124F/00/en “Commuwin II” operating program

Connection

The table provides an overview of the Commuwin connections.

Note!

The 7500 RTG can also be operated locally using the keys. If operation is prevented by

the keys being locked locally, parameter entry via communication is not possible either.

Interface

Hardware

Server

Device list

HART

Commubox FXA 191 to HART

Computer with RS-232C interface

HART

Connected instrument

Interface FXN 672

Gateway for MODBUS, PROFIBUS,

FIP, INTERBUS, etc.

Computer with

RS-232C interface or

PROFIBUS card

ZA 673 for

PROFIBUS

ZA 672 for

other

List of all rack bus modules:

the required FXN 672 must

be selected

Содержание 7532











































































































Результаты поиска

Содержание 7532

Отзывы:

Похожие инструкции для 7532

Бренды по названию

Популярные бренды

Varec 7532, Инструкция по установке и эксплуатации

Результаты поиска

Содержание 7532

Отзывы:

Похожие инструкции для 7532

Бренды по названию

Популярные бренды