Van Der Stahl FAS-402-CH Series, Руководство по эксплуатации

Страница: 53 / 68

53 53
FAS-402-CH/FAS-602-CH Series Operating Instructions Ver. 1.05E
Commodity name Nozzle type vacuum sealer
Model name FAS-402-CH FAS-402-CH-10D FAS-602-CH FAS-602-CH-10D
Power source * Note 1
Maximum power
consumption
N:PPKHDWHU
N:PPKHDWHU
2.6kW
N:PPKHDWHU
N:PPKHDWHU
2.9kW
Power cord * Note 2
Air source Compatible air compressor: 0.75kW, 80L/min, 0.5MPa or greater
Air pressure setting value: 0.35 MPa
Vacuum source %XLOWLQSXPS'236&VSHFLDON3D/PLQE\FDWDORJ
Control style Microcomputer
Sealing style Single-side heating Double-side heating Single-side heating Double-side heating
Driving style Air cylinder 63mm X 2pcs.
Sealing length 400 mm 600mm
Sealing width 5mm and 10mm
LQWHUFKDQJHDEOH
10mm
5mm and 10mm
LQWHUFKDQJHDEOH
10mm
Height of sealing surface PPIURPERWWRPWRVHDOLQJVXUIDFH
Seal heating time 0.0 ~ 2.0 seconds
Seal heating temperature 60 ~ 250
°
C / 140 ~ 480
°
F
Seal cooling temperature * Note 3 40 ° C/ 100 ° F ~ set-up temperature
Vacuum time 0.1 ~ 99.9 seconds
Vacuum degree * Note 4 -10 ~ -100 kPa
Nozzle stroke 75mm
Outside dimensions W 560mm X L 888mm X H 300mm
LQFOXGLQJWKHWDEOH
W 675mm X L 888mm X H 300mm
LQFOXGLQJWKHWDEOH
Table dimensions W 396mm X L 350mm W 596mm X L 350mm
Optional printer Hot Stamp Printer FEP-V-N2 can be installed at the shipment with FAS-402
6HDOLQJDUHDFRYHURSWLRQ Polycarbonate cover to prevent the pinching
6WDQGRSWLRQ
Angle is changed by three steps (10
°
, 15
°
, 20
°
* Note 1 7KHYROWDJHVSHFL¿FDWLRQRI\RXUXQLWLVOLVWHGRQWKHODEHOZKLFKGLVSOD\VWKHVHULDOQXPEHU
This label can be found on the machine body.
* Note 2 Please put the plug in your country style.
* Note 3 Set the cooling temperature lower than the heating temperature. If the cooling temperature
LVVHWWRRFORVHWRKHDWLQJWHPSHUDWXUHWKHFRROLQJZLOOQRWEHVXI¿FLHQWDQGWKHFRQVXPDEOH
parts tends to be damaged faster.
* Note 4 Structurally, the nozzle vacuum system will cause attainable vacuum level to be erratic when
operating the machine in low vacuum of between -1 to -20 kPa. Additional discussion is
necessary for low vacuum operation.
Anti-overheating mechanism D:KHQRYHUKHDWLQJRFFXUVLHZKHQWKHSRZHUFRQWLQXHVWREHGLVWULEXWHGWRWKH
KHDWLQJHOHPHQWIRUORQJHUWKDQVHFRQGVWKHEUHDNHUWXUQVRIIDQGWKHSRZHULV
shutoff.
E:KHQWKHVHWWHPSHUDWXUHLVQRWUHDFKHGZLWKLQVHFRQGVWKHLQLWLDOFRQGLWLRQLV
restored and an error message will appear on the control panel screen.
Lever drive The lever uses spring action to clamp down on the bag so that no forcible pressure is
DSSOLHGZKHQ¿QJHURURWKHUIRUHLJQREMHFWVJHWFDXJKW3UHVVXUHRIGLDPHWHUF\OLQGHU
output force is applied when sealing.
Emergency reset mechanism When the lever is being lowered, removing foot from the foots witch will raise the lever
from its lowered position.
Automatic reset upon anomaly
detection :KHQWKHOHYHULVEHLQJSUHVVHGGRZQLIDIRUHLJQREMHFWHJD¿QJHULVFDXJKWLQWKH
sealing area and is preventing the sealing process from proceeding to the next step, the
lever will return to its initial position after one second.
Heat signal Heating starts at the same time when lever is closed. Heating signal is sent when
PLFURVZLWFKDQGF\OLQGHUORZHUVHQVRUDUHWXUQHGRQGRXEOHVWUXFWXUH
10 Specification
Safety measures