UTAS BX7000 Скачать руководство пользователя страница 11

Страница: 11 / 64

1 Turn on the power to start using BX7000.

Move the power switch at the backside of

BX7000

to the “

”.

Note

“I”

on the power switch means “Power On”,

while

“O”

means “Power Off”.

2 When you turn on BX7000 for the very first time, you will be

directed to “Device Home”.

The “Device Home” screen will appear followed by a loading screen

which will be displayed and stay for approximately 45 seconds as

immediately as after the LCD screen is turned on. Since there is no
available device registered in “Device Home”, you must register

devices before starting to use the mode.

Note

1. When you open “Device Home” for the first time, you will be

informed with the mode unavailability messages. This message will

no longer appear once a device button is registered.

2. You cannot use buttons at first. When you press an

button, you will be informed with the button‟s function through a

message. However, this message will be no longer displayed once

you register a device and use the button for the device.

3. Press the

[SET]

button shortly at the upper right side of the “Device

Home” screen. You will be directed to “Device Setup” menu.

Power On

Tip

. Restarting from the Sleep Mode

The LCD screen will be automatically switched to the Sleep mode, and

turned off at the time that was set up by the user. (Refer to the page 16,
“LCD Timeout”.)

If you wish to wakeup the Sleep mode and display the LCD screen;

Getting Started

※

BX7000 screen image in the manual

may be slightly different from that as

actually set in a screen.

BX7000 is a wall-mountable touch panel, so it is not powered by batteries but connected directly with electricity.

Power should be supplied uninterrupted using DC12V adaptor. Connect using terminal block after making sure

that power connection port is in a working condition.

☞

Caution !

Power connected with other than power port, BX7000 cannot be used due to damage in plate.

Содержание BX7000

































































Результаты поиска

Содержание BX7000

Отзывы:

Похожие инструкции для BX7000

Бренды по названию

Популярные бренды

UTAS BX7000, Руководство пользователя

Результаты поиска

Содержание BX7000

Отзывы:

Похожие инструкции для BX7000

Бренды по названию

Популярные бренды