Unitech MS852Plus Auto Switching Скачать руководство пользователя страница 50

Страница: 50 / 99

- 35 -

unitech is a registered trademark of unitech Electronics Co., Ltd.

MS852Plus User’s Manual

3.3.10 UPC-A

Code UPC-A On*

Default All UPC-A Settings

Code UPC-A Off

Note: To convert UPC-A bar codes to EAN-13, see

Convert UPC-A to EAN-13.

3.3.10.1 UPC-A Check Digit

This selection allows you to specify whether the check digit should be

transmitted at the end of the scanned data or not. Default = On.

On*

Off

3.3.10.2 UPC-A Number System

The numeric system digit of a U.P.C. symbol is normally transmitted at the

beginning of the scanned data, but the unit can be programmed so it will not

transmit it. Default = On.

On*

Off

Содержание MS852Plus Auto Switching


































































































Результаты поиска

Содержание MS852Plus Auto Switching

Отзывы:

Похожие инструкции для MS852Plus Auto Switching

Бренды по названию

Популярные бренды

Unitech MS852Plus Auto Switching, Руководство пользователя

Результаты поиска

Содержание MS852Plus Auto Switching

Отзывы:

Похожие инструкции для MS852Plus Auto Switching

Бренды по названию

Популярные бренды