Unitech MS852Plus Auto Switching Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 99

background image

ix

© 2019 unitech Electronics Co., Ltd. All rights reserved.

unitech is a registered trademark of unitech Electronics Co., Ltd.

MS852Plus User’s Manual

Storage and safety notice

Although charged batteries may be left unused for several months, their
capacity may be depleted due to build up of internal resistance. If this happens,
they will require recharging prior to use. Batteries may be stored at
temperatures between -20°C to 60°C, however they may deplete more rapidly
at higher temperatures. It is recommended to store batteries at room
temperature.

* The message above only applies to the usage of the removable batteries.

For the products with non-removable batteries / without batteries, please refer to
the specification of each product.

Product Operation and Storage Notice

The unitech product has applicable operation and storage temperature
conditions. Please follow the limitation of suggested temperature conditions to
avoid failure, damage or malfunction.

*

For applicable temperature conditions, please refer to the specification of each

product.

«
...
9
10
11
12
13
...
»

Содержание MS852Plus Auto Switching




































































































Отзывы:

Нет отзывов

Похожие инструкции для MS852Plus Auto Switching

Бренд: Wasp Страницы: 12

Бренд: Wasp Страницы: 44

Бренд: Symbol Страницы: 6

FlashMover MS-Direct

Бренд: Microdia Страницы: 5

Бренд: Opticon Страницы: 8

DuraScan 700 Series

Бренд: Socket Страницы: 49

Бренд: Unitech Страницы: 90

Бренд: Symbol Страницы: 352

Бренд: Code Страницы: 16

Бренд: SATO Страницы: 16

IDMR-PBT93133TEB

Бренд: IDTECH Страницы: 18

Z800 - Workstation - 6 GB RAM

Бренд: HP Страницы: 9

Бренд: Atid Страницы: 32

Бренд: Cansec Страницы: 6

Бренд: Bematech Страницы: 500

Бренд: Banner Страницы: 17

Бренд: Ier Страницы: 17

Бренд: Rosslare Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды