Unitech MS852Plus Auto Switching Скачать руководство пользователя страница 53

Страница: 53 / 99

- 38 -

unitech is a registered trademark of unitech Electronics Co., Ltd.

MS852Plus User’s Manual

3.3.10.7 UPC-A/EAN-13 with Extended Coupon Code

Use the following codes to enable or disable UPC-A and EAN-13 with

Extended Coupon Code. When left on the default setting (Off), the scanner

treats Coupon Codes and Extended Coupon Codes as single bar codes. If you

scan the Allow Concatenation code, when the scanner sees the coupon code

and the extended coupon code in a single scan, it transmits both as one

symbology. Otherwise, it transmits the first coupon code it reads. If you scan

the Require Concatenation code, the scanner must see and read the coupon

code and extended coupon code in a single read to transmit the data. No data

is output unless both codes are read. Default = Off.

3.3.10.8 Coupon GS1 DataBar Output

If you scan coupons that have both UPC and GS1 DataBar codes, you may

wish to scan and output only the data from the GS1 DataBar code. Scan the

GS1 Output On code below to scan and output only the GS1 DataBar code

data. Default = GS1 Out-put Off.

Off*

Allow Concatenation

Require Concatenation

GS1 Output Off *

GS1 Output On

Содержание MS852Plus Auto Switching


































































































Результаты поиска

Содержание MS852Plus Auto Switching

Отзывы:

Похожие инструкции для MS852Plus Auto Switching

Бренды по названию

Популярные бренды

Unitech MS852Plus Auto Switching, Руководство пользователя

Результаты поиска

Содержание MS852Plus Auto Switching

Отзывы:

Похожие инструкции для MS852Plus Auto Switching

Бренды по названию

Популярные бренды