Unitech MS852Plus Auto Switching Скачать руководство пользователя страница 40

Страница: 40 / 99

- 25 -

unitech is a registered trademark of unitech Electronics Co., Ltd.

MS852Plus User’s Manual

3.3.2.7 Code 39 Code Page

Code pages define the mapping of character codes to characters. If the data

received does not display with the proper characters, it may be because the

bar code being scanned was created using a code page that is different from

the one the host program is expecting. If this is the case, scan the bar code

below, select the code page with which the bar codes were created (

see ISO

2022/ISO 646 Character Replacements

), and scan the value and the Save bar

code from the

Programming Chart

. The data characters should then appear

properly.

Code 39 Code Page

3.3.3 Interleaved 2 of 5

Interleaved 2 of 5 On*

Default All Interleaved 2 of 5 Settings

Interleaved 2 of 5 Off

Содержание MS852Plus Auto Switching


































































































Результаты поиска

Содержание MS852Plus Auto Switching

Отзывы:

Похожие инструкции для MS852Plus Auto Switching

Бренды по названию

Популярные бренды

Unitech MS852Plus Auto Switching, Руководство пользователя

Результаты поиска

Содержание MS852Plus Auto Switching

Отзывы:

Похожие инструкции для MS852Plus Auto Switching

Бренды по названию

Популярные бренды