Unitech MS852Plus Auto Switching Скачать руководство пользователя страница 72

Страница: 72 / 99

- 57 -

unitech is a registered trademark of unitech Electronics Co., Ltd.

MS852Plus User’s Manual

3.4.7.1 UPC/EAN Version

Scan the UPC/EAN Version On bar code to decode GS1 Composite symbols

that have a U.P.C. or an EAN linear compo-nent. (This does not affect GS1

Composite symbols with a GS1-128 or GS1 linear component.)

Default = UPC/EAN Ver-sion Off.

Note: If you scan coupons that have both UPC and GS1 DataBar codes, you

may wish to scan and output only the data from the GS1 DataBar code.

See Coupon GS1 DataBar Output for further information.

Off *

3.4.7.2 GS1 Composite Code Message Length

Scan the bar codes below to change the message length. Refer to

Message

Length Description

for additional information. Minimum and Maximum lengths

= 1-2435. Minimum Default = 1, Maximum Default =2435.

Minimum Message Length

Maximum Message Length

Содержание MS852Plus Auto Switching


































































































Результаты поиска

Содержание MS852Plus Auto Switching

Отзывы:

Похожие инструкции для MS852Plus Auto Switching

Бренды по названию

Популярные бренды

Unitech MS852Plus Auto Switching, Руководство пользователя

Результаты поиска

Содержание MS852Plus Auto Switching

Отзывы:

Похожие инструкции для MS852Plus Auto Switching

Бренды по названию

Популярные бренды