Unitech MS852Plus Auto Switching Скачать руководство пользователя страница 12

Страница: 12 / 99

unitech is a registered trademark of unitech Electronics Co., Ltd.

MS852Plus User’s Manual

Adapter Notice

1. Please do not leave the power adapter in the socket when it is not

connected to your unitech product for charging.

2. Please remove the power adapter when the battery is fully recharged.

3. The bundled power adapter that comes with your unitech product is not

meant to be used outdoors. An adapter exposed to water or rain, or a very

humid environment can cause damage to both the adapter and the

product.

4. Please only use the bundled power adapter or same specification of

adapter to charge your unitech product. Using the wrong power adapter

can damage your unitech product.

* The message above only applies to the product connected to the adapter.

For the products without using the adapters, please refer to the specification of
each product.

Hearing Damage Warning

Zx.3 Warning

The warning shall be placed on the equipment, or on the packaging, or in the instruction

manual and shall consist of the following:

- the symbol of Figure 1 with a minimum height of 5 mm; and

- the following wording, or similar :

To prevent possible hearing damage, do not listen at high volume levels for long periods.

Alternatively, the entire warning may be given through the equipment display during use, when

the user is asked to acknowledge activation of the higher level.

Содержание MS852Plus Auto Switching


































































































Результаты поиска

Содержание MS852Plus Auto Switching

Отзывы:

Похожие инструкции для MS852Plus Auto Switching

Бренды по названию

Популярные бренды

Unitech MS852Plus Auto Switching, Руководство пользователя

Результаты поиска

Содержание MS852Plus Auto Switching

Отзывы:

Похожие инструкции для MS852Plus Auto Switching

Бренды по названию

Популярные бренды