Unitech MS852Plus Auto Switching Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 99

background image

i

© 2019 unitech Electronics Co., Ltd. All rights reserved.

unitech is a registered trademark of unitech Electronics Co., Ltd.

MS852Plus User’s Manual

Preface

About This Manual

Thank you for purchasing the unitech product.
This manual explains how to install, operate and maintain our product.
No part of this publication may be reproduced or used in any form, or by any electrical or
mechanical means, such as photocopying, recording, or information storage and retrieval
systems, without permission in writing from the manufacturer. The material in this manual
is subject to change without notice. All product and company names are trademarks,
service marks, or registered trademarks of their respective owners.

Regulatory Compliance Statements

FCC Warning Statement

This device has been tested and found to comply with the limits for a Class B

digital device, pursuant to part 15 of the FCC rules. These limits are designed

to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may

cause harmful interference with radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference with radio or television reception,

which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following

measures:

–Reorient or relocate the receiving antenna.

–Increase the separation between the equipment and receiver.

–Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

–Consult the dealer or an experienced radio/TV technician for help.

«
1
2
3
4
5
...
»

Содержание MS852Plus Auto Switching




































































































Отзывы:

Нет отзывов

Похожие инструкции для MS852Plus Auto Switching

T15 Mifare Reader Black

Бренд: Gallagher Страницы: 13

Бренд: Wasp Страницы: 28

Orpak M09680B136

Бренд: Gasboy Страницы: 12

Бренд: Obreey Страницы: 54

Бренд: Datalogic Страницы: 37

Бренд: Climax Technology Страницы: 4

Бренд: Krüger & Matz Страницы: 21

Бренд: Wasp Страницы: 41

Бренд: Wasp Страницы: 52

Бренд: Datalogic Страницы: 292

Бренд: Unitech Страницы: 65

Бренд: Visionis Страницы: 18

Бренд: Icy Box Страницы: 8

Бренд: Icy Box Страницы: 12

Бренд: Icy Box Страницы: 12

Бренд: Pocketbook Страницы: 20

Бренд: POCKETALK Страницы: 59

Бренд: Pocketbook Страницы: 69

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды