Unitech MS852Plus Auto Switching Скачать руководство пользователя страница 63

Страница: 63 / 99

- 48 -

unitech is a registered trademark of unitech Electronics Co., Ltd.

MS852Plus User’s Manual

3.3.15.1 MSI Check Character

Different types of check characters are used with MSI bar codes. You can

program the scanner to read MSI bar codes with Type 10 check characters.

Default = Validate Type 10, but Don’t Transmit. When Check Character is set

to Validate Type 10/11 and Transmit, the scanner will only read MSI bar codes

printed with the specified type check character(s), and will transmit the

character(s) at the end of the scanned data. When Check Character is set to

Validate Type 10/11, but Don’t Transmit, the unit will only read MSI bar codes

printed with the specified type check character(s), but will not transmit the

check character(s) with the scanned data.

Validate Type 10, but Don’t Transmit*

Validate Type 10 and Transmit

Validate 2 Type 10 Characters, but Don’t Transmit

Validate 2 Type 10 Characters and Transmit

Validate Type 10 then Type 11 Character, but Don’t Transmit

Validate Type 10 then Type 11 Character and Transmit

Disable MSI Check Characters

Содержание MS852Plus Auto Switching


































































































Результаты поиска

Содержание MS852Plus Auto Switching

Отзывы:

Похожие инструкции для MS852Plus Auto Switching

Бренды по названию

Популярные бренды

Unitech MS852Plus Auto Switching, Руководство пользователя

Результаты поиска

Содержание MS852Plus Auto Switching

Отзывы:

Похожие инструкции для MS852Plus Auto Switching

Бренды по названию

Популярные бренды