Unitech MS852Plus Auto Switching Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 99

background image

vii

© 2019 unitech Electronics Co., Ltd. All rights reserved.

unitech is a registered trademark of unitech Electronics Co., Ltd.

MS852Plus User’s Manual

Battery Notice

1. To guarantee optimal performance, it is recommended that rechargeable

batteries be replaced every year, or after 500 charging cycles are
completed. It is normal for the battery to balloon or expand after one year
or 500 cycles. Although it does not cause damage, it cannot be used again
and must be disposed of according to the location's safe battery disposal
procedures.

2. If a battery performance decreases more than 20%, the battery is at the

end of its life cycle. Stop use and ensure the battery is disposed of
properly.

3. The length of time that a battery lasts depends on the battery type and

how the device is used. Conserve the battery life by doing the following:



Avoid fully uncharging the battery because this places additional

strain on it. Several partial uncharges with frequent charges are better

than a fully uncharged battery. Charging a partially charged battery

does not cause harm to the unit.



Keep the battery cool. Avoid hot vehicles. For prolonged

storage, keep the battery at a 40% charge level.



Do not leave the battery uncharged and unused for an extended

period of time, the battery will wear out and the longevity of the

battery will be at least half of one with frequent charges.

4. Protect battery life by not over or under charging the battery.

5. Please do not leave battery unused for long time without charging it.

Despite unitech’s safety precautions, the battery pack may begin to

change shape. If so, stop using it immediately. Please check to see if you

are using a proper power adapter to charge the battery or contact your

service provider for service.

6. If you cannot charge the battery after it has been idle for an extended

period of time and it begins to heat up, please do not try to charge it. It

may not be functional anymore.

7. Please only use the original battery from unitech. Using a third party

battery can damage our products. Please note that when such damage

occurs, it is not covered by your warranty.

«
...
7
8
9
10
11
...
»

Содержание MS852Plus Auto Switching




































































































Отзывы:

Нет отзывов

Похожие инструкции для MS852Plus Auto Switching

Бренд: Accu-Sort Страницы: 2

Бренд: IDTECK Страницы: 12

Gryphon 4200 Series

Бренд: Datalogic Страницы: 44

Бренд: Wasp Страницы: 5

Smart Connector

Бренд: KUARIO Страницы: 20

Бренд: DKS Страницы: 2

Бренд: SureFlap Страницы: 6

Бренд: Printronix Страницы: 26

C33-00-486000Z4

Бренд: Datamax Страницы: 10

Бренд: Gemalto Страницы: 145

Бренд: TECH FASS Страницы: 11

Бренд: Cub Страницы: 41

Бренд: Saveo Scan Страницы: 178

Бренд: SmarTerminal Страницы: 14

SAVEO-SCAN-M22D-H

Бренд: Saveo Scan Страницы: 3

SAVEO-SCAN-R11D-BH

Бренд: Saveo Scan Страницы: 23

Бренд: Uconnect Страницы: 4

Quick Check 200 Series

Бренд: Hand Held Products Страницы: 72

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды