Unitech MS852Plus Auto Switching Скачать руководство пользователя страница 38

Страница: 38 / 99

- 23 -

unitech is a registered trademark of unitech Electronics Co., Ltd.

MS852Plus User’s Manual

3.3.2.4 Code 39 Append

This function allows the scanner to append the data from several Code 39 bar

codes together before transmitting them to the host computer. When the

scanner encounters a Code 39 bar code with the append trigger character(s),

it buffers Code 39 bar codes until it reads a Code 39 bar code that does not

have the append trigger. The data is then transmitted in the order in which the

bar codes were read (FIFO). Default = Off.

Off *

3.3.2.5 Code 32 Pharmaceutical (PARAF)

Code 32 Pharmaceutical is a form of the Code 39 symbology used by Italian

pharmacies. This symbology is also known as PARAF.

Note: Trioptic Code must be turned off while scanning Code 32 Pharmaceutical codes.

Off *

Содержание MS852Plus Auto Switching


































































































Результаты поиска

Содержание MS852Plus Auto Switching

Отзывы:

Похожие инструкции для MS852Plus Auto Switching

Бренды по названию

Популярные бренды

Unitech MS852Plus Auto Switching, Руководство пользователя

Результаты поиска

Содержание MS852Plus Auto Switching

Отзывы:

Похожие инструкции для MS852Plus Auto Switching

Бренды по названию

Популярные бренды