µ-Dimension 180-00108 uPrint Скачать руководство пользователя

Страница: 12 / 76

Setup

Document Number 206465-0001

User Guide

Setup

Minimum requirements:

Workspace requirements:

Facility requirements & environmental specifications:

Work station requirements:

See release notes...

http://www.uPrintDimension.com/productinformation/customerinfo

System specifications

Printer height

762mm (30 in.)

Printer width

660mm (26 in.)

Printer depth

660mm (26 in.)

Printer weight

59 Kg (130 lbs.)

Material bay height

153mm (6 in.)

Material bay width

660mm (26 in.)

Material bay depth

660mm (26 in.)

Material bay weight

17 Kg (37 lbs.)

Air circulation

115 mm (4.5 in.) minimum space behind unit for air circulation.

153 mm (6 in.) minimum space around the printer for air circulation.

Installation location

Stable flat surface capable of holding 100Kg (220 lbs).

Facility requirements

Dedicated outlet voltage
requirements (Nominal):

100-120 VAC, 50/60 Hz, 15 Amp minimum (20 Amp recom-
mended)
–or–
200-240 VAC, 50/60 Hz, 7 Amp minimum (10 Amp recommended)

Ambient temperature:

15-30°C (60-86°F) Operating

Relative humidity:

30-70%, Non-condensing Operating

Network connection:

Ethernet 10/100 Base T

Optional UPS for power
interruptions:

Rated Power – 1440 VA
Output Power – 1500 watts

Heat emission

3050 BTU/hr while powering up

2550 BTU/hr while building

Noise level

55dBA while idle and 62dBA while operating

Содержание 180-00108 uPrint













































































Результаты поиска

Содержание 180-00108 uPrint

Отзывы:

Похожие инструкции для 180-00108 uPrint

Бренды по названию

Популярные бренды

µ-Dimension 180-00108 uPrint, Руководство пользователя

Результаты поиска

Содержание 180-00108 uPrint

Отзывы:

Похожие инструкции для 180-00108 uPrint

Бренды по названию

Популярные бренды