µ-Dimension 180-00108 uPrint Скачать руководство пользователя

Страница: 20 / 76

Setup

Document Number 206465-0001

User Guide

Power cable

Connecting the power cable:

1. Connect the power cable to the back of the printer.

Connect the power cable to the dedicated power outlet. See

Figure 15

Note:

Do not use an extension cord or a power strip, using these
can possibly cause intermittent power issues.

Figure 15: Power cable connection

Network/Crossover connections

Connecting the network cable:

1. Connect the network cable (blue) to the network connection at the back of the printer. See

Figure 16

Connect the network cable to the dedicated outlet or network hub.

If not using a network and connecting directly to a PC, you will need to use a crossover cable.

Connecting the crossover cable:

1. Connect the crossover cable (orange) to the network connection at the back of the printer. See

Figure

Connect the crossover cable to the computer.

Содержание 180-00108 uPrint













































































Результаты поиска

Содержание 180-00108 uPrint

Отзывы:

Похожие инструкции для 180-00108 uPrint

Бренды по названию

Популярные бренды

µ-Dimension 180-00108 uPrint, Руководство пользователя

Результаты поиска

Содержание 180-00108 uPrint

Отзывы:

Похожие инструкции для 180-00108 uPrint

Бренды по названию

Популярные бренды