µ-Dimension 180-00108 uPrint Скачать руководство пользователя

Страница: 26 / 76

Setup

Document Number 206465-0001

User Guide

C. Enter the dynamic IP address for your printer (from step 2B) in the appropriate field.

D. Select the appropriate printer type from the drop down list.

E. Click

Add Printer

and close the

3D Printer

pop-up window.

If you get an

“Error: Unable to connect to printer”

message it may be that your PC is not

configured for dynamic networking. To configure your PC for dynamic networking:

From the

Control Panel

of your PC, double click on

Network and Internet Connections

ii.

Double click on

Network Connections

, then double click on

Local Area Connection

iii. Scroll the

Local Area Network Connection Properties

window to find the

Internet Protocol

(TCP/IP)

selection. Click on

Internet Protocol (TCP/IP)

and then click on the

Properties

button.

iv. From the

General

tab of the

Internet Protocol (TCP/IP)

properties pop-up window, click on

the

Obtain IP Address Automatically

radio button.

Click

and then

again.

vi. After allowing your PC a minute or so to adjust to the new setting, your PC should connect to

your printer.

vii. If you are still unable to connect to your printer, recheck your connections and settings.

System Software

The system software is factory loaded on the printer. Due to occasional changes you may need to update
the printer system software.

Updating system software:

1. From the uPrint display panel, press

Maintenance

Press

System

Press

Load Upgrade

. The printer will then display

“Send upgrade from workstation”

followed by

the printer’s IP address.

Open CatalystEX and click on the

Printer Services

tab.

Click on the

Update Software

button. CatalystEX will now connect to the printer and will prompt you to

locate the upgrade file. Navigate CatalystEX to the CD where the upgrade file is located. The update
will automatically be loaded on to the printer. After the update has been loaded, the display will show

Verifying update

When verification is complete, the display will show

Reboot to complete

. Select

Yes

. The printer will

now reboot and return to

Idle

Press the maintenance button and verify the updated version was installed correctly.

Содержание 180-00108 uPrint













































































Результаты поиска

Содержание 180-00108 uPrint

Отзывы:

Похожие инструкции для 180-00108 uPrint

Бренды по названию

Популярные бренды

µ-Dimension 180-00108 uPrint, Руководство пользователя

Результаты поиска

Содержание 180-00108 uPrint

Отзывы:

Похожие инструкции для 180-00108 uPrint

Бренды по названию

Популярные бренды