Tyco Fire & Security CWSI CP-3600 Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 81

Tyco Fire & Security CWSI CP-3600 Скачать руководство пользователя страница 29

P/N CWSI-IM-C3K6 Rev. F

© 2017 Johnson Controls. All rights reserved. All specifications and other information shown were current as of document revision
date and are subject to change without notice.

29

4.3.4 Supervisory Setup

The CP-3600(+) has the option of self-restoring supervisory signals. This menu will allow both the
option of making Alarm C devices supervisory type and turning the auto-restore feature on. Even though
these features can be selected after boot up it is advisable to activate one or both of these features
now if either one will be needed in the installation. Choosing to turn supervisory self-restore on after
boot up may require the system to reboot for the change to take effect. Refer to the supervisory section
for more information.

To look at the supervisory setup and change it if necessary, highlight the Supervisory Setup menu
choice and press ENTER. The screen below will be shown.

To change either setting highlight it and press ENTER. Use the UP/DOWN buttons to choose On or Off
then press enter. When you are done making the desired changes press the Save soft key to save the
change and display the Initial Configuration Menu.

This completes initial configuration of the system. Press the DONE soft key to go to the CP-3600(+)
main screen.

Note: If any alarms or troubles are in process the main screen will not be shown

after pressing DONE. The in process alarms or troubles will be shown instead.

The Time and Date, Password and Base code can be modified any time after the initial configuration
by pressing the Config soft key while the main system CP-3600(+) ok screen is displayed.

4.4 Device, Annunciator, Repeater and CP-3600(+) Info
Programming

This section describes how to input zone assignment, alarm priority, device type and description
information for devices, annunciators and repeaters. Entering this information is crucial for proper
activation of notification appliances and audible notification devices as well as notifying responding
authorities of the precise location of an alarm in process.

S u p e r v i s o r y S e t u p

C a n c e l

A l a r m C S u p e r v i s o r y : O f f

                                          S u p e r v i s o r y   A u t o - R e s t o r e :     O f f

«
...
27
28
29
30
31
...
»

Содержание CWSI CP-3600


















































































Отзывы:

Нет отзывов