Trillium 10-WSP Скачать руководство пользователя страница 9

Страница: 9 / 72

WSP™

DATA SHEET

WSP™ SELF-PRIMER PUMPS

WSP-D300_10

Rev. 3

01/09/20

YOUR PUMP HAS BEEN ENGINEERED TO PUMP LIQUIDS THAT CONTAIN SOLIDS OR

SLURRIES. AT NO TIME SHOULD THE LIQUID BE VOLATILE, CORROSIVE, OR

COMBUSTIBLE. FAILURE TO DO SO COULD DAMAGE THE PUMP OR RESULT IN

INJURY.

AFTER THE PUMP CASING HAS BEEN FILLED, REINSTALL AND TIGHTEN THE FILL

PLUG. FAILURE TO OPERATE THE PUMP WITHOUT ALL CONNECTION PIPING

SECURELY INSTALLED COULD CAUSE LIQUID IN THE PUMP TO BE FORCED OUT

UNDER PRESSURE AND MAY RESULT IN INJURY.

PRIOR TO WORKING ON THIS PUMP, ALWAYS LOCK OUT OR DISCONNECT THE

PUMP FROM ITS POWER SOURCE. IT MUST REMAIN INOPERABLE DURING REPAIRS.

NO PERSON SHOULD ATTEMPT TO OPEN OR SERVICE THIS PUMP BEFORE

BECOMING THOROUGHLY FAMILIAR WITH ALL THE PROCEDURES OUTLINED

IN THIS MANUAL.

1. PLEASE STUDY THESE INSTRUCTIONS CAREFULLY.

2. WHEN PERFORMING EQUIPMENT MAINTENANCE, THE EQUIPMENT

ELECTRICAL SERVICE MUST BE LOCKED OUT WITH AN APPROVED

LOCKOUT AND KEY.

3. IF THE PUMP HAS OVERHEATED, ALLOW SUFFICIENT TIME FOR THE

PUMP TO COMPLETELY COOL BEFORE ATTEMPTING TO OPEN OR

SERVICE THE PUMP.

4. CAREFULLY CHECK THE TEMPERATURES BEFORE OPENING ANY

COVERS, PLATES, OR PLUGS.

5. CLOSE THE SUCTION AND DISCHARGE VALVES.

6. CAREFULLY AND SLOWLY VENT THE PUMP.

Содержание 10-WSP









































































Результаты поиска

Содержание 10-WSP

Отзывы:

Trillium 10-WSP, Инструкция по установке, эксплуатации и обслуживанию, Страница: 9 / 72

Результаты поиска

Содержание 10-WSP

Отзывы: