Trillium 10-WSP Скачать руководство пользователя страница 59

Страница: 59 / 72

WSP™

DATA SHEET

WSP™ SELF-PRIMER PUMPS

WSP-D300_10

Rev. 3

01/09/20

minimum vacuum of 20-inches (508 mm) of mercury when fully operational.

If there is not enough suction, the pump is not pulling adequately. Inspect for

possible air leaks. These may be found in the gasket, the discharge valve or

the seal.

When the pump is primed, open the suction line and read the vacuum gauge

with the pump operating at normal speed then shut off the pump. When the

pump is off, the reading on the vacuum gauge should lower rapidly to static

suction lift then quickly stabilize. Verify that the gauge connection is properly

sealed before inspecting the pump vacuum gauge to determine the location

of any leaks.

D. STOPPING

Severe tremors that jolt the pump and piping can severely impair or damage the

equipment when fluids being pumped are suddenly stopped. To avoid costly repairs

or replacement of the equipment, slowly shut all the connecting valves.

When using an engine to drive the pumps, slow the throttle speed gradually then

permit the engine to idle for a few minutes before completing the shutdown.

IN HIGH DISCHARGE HEAD APPLICATIONS THE DISCHARGE THROTTLING VALVE

MUST BE GRADUALLY CLOSED BEFORE THE PUMP IS STOPPED.

Once the pump is stopped, either disconnect or block the power source to be sure

the pump will stay dormant during inspection, maintenance or repair.

DO NOT OPERATE PUMP WITH BOTH SUCTION AND DISCHARGE VALVES CLOSED

OR WITH SUCTION OR DISCHARGE BLOCKED BY CLOGGING – THIS COULD CAUSE

DAMAGE AND IS DANGEROUS. THESE PUMPS ARE TO BE USED FOR LIQUID

SERVICE ONLY. EXCESSIVE PRESSURE CAN CAUSE MALFUNCTION LEADING TO

INJURY.

1. General Information for Pump Storage

a. To maintain pump integrity, always store in a clean, dry area away from

harsh weather.

b. Do not store the pump where there is rising water.

Содержание 10-WSP









































































Результаты поиска

Содержание 10-WSP

Отзывы:

Trillium 10-WSP, Инструкция по установке, эксплуатации и обслуживанию, Страница: 59 / 72

Результаты поиска

Содержание 10-WSP

Отзывы: