Trillium 10-WSP Скачать руководство пользователя страница 39

Страница: 39 / 72

WSP™

DATA SHEET

WSP™ SELF-PRIMER PUMPS

WSP-D300_10

Rev. 3

01/09/20

PUMP REQUIRES TOO MUCH POWER

POSSIBLE CAUSE

PROBABLE REMEDY

Pump speed running too fast.

Check driver output; check that sheaves

or couplings are correctly sized.

Discharge head too low.

Adjust discharge valve.

Liquid is to viscous.

Dilute if possible.

Bearing(s) seized.

Disassemble pump and check

bearing(s).

PUMP CLOGS FREQUENTLY

POSSIBLE CAUSE

PROBABLE REMEDY

Liquid is to viscous.

Dilute if possible.

Discharge flow is too slow.

Open discharge valve fully to increase

flow rate, and run power source at

maximum governed speed.

Suction check valve or foot valve clogged or

binding.

Clean valve.

EXCESSIVE NOISE

POSSIBLE CAUSE

PROBABLE REMEDY

Pump cavitating

Reduce suction lift and/or friction losses

in suction line. Record vacuum and

pressure gauge readings, and consult

local representative or factory.

Pump is sucking air.

Locate and eliminate source of air

bubble.

Pump or drive not mounted securely.

Secure mounting hardware.

Impeller plugged, blocked, or damaged.

Clean out debris and replace damaged

parts.

BEARINGS RUN TOO HOT

POSSIBLE CAUSE

PROBABLE REMEDY

Bearing temperature is rising above normal.

Check bearing temperature regularly to

monitor any increase.

Low or incorrect lubricant.

Check for proper type and level of

lubricant.

Suction and discharge lines not properly

supported.

Check piping installation for proper

support.

Drive not properly aligned.

Align drive properly.

Содержание 10-WSP









































































Результаты поиска

Содержание 10-WSP

Отзывы:

Trillium 10-WSP, Инструкция по установке, эксплуатации и обслуживанию, Страница: 39 / 72

Результаты поиска

Содержание 10-WSP

Отзывы: