Trillium 10-WSP Скачать руководство пользователя страница 18

Страница: 18 / 72

WSP™

DATA SHEET

WSP™ SELF-PRIMER PUMPS

WSP-D300_10

Rev. 3

01/09/20

To take apart and repair the power source, refer to the documentation supplied with

your power source, or contact your local power source representative.

NO PERSON SHOULD ATTEMPT TO OPEN OR SERVICE THIS PUMP BEFORE

BECOMING THOROUGHLY FAMILIAR WITH ALL THE PROCEDURES OUTLINED

IN THIS MANUAL.

1. PLEASE STUDY THESE INSTRUCTIONS CAREFULLY.

2. WHEN PERFORMING EQUIPMENT MAINTENANCE, THE EQUIPMENT

ELECTRICAL SERVICE MUST BE LOCKED OUT WITH AN APPROVED

LOCKOUT AND KEY.

3. IF THE PUMP HAS OVERHEATED, ALLOW SUFFICIENT TIME FOR THE

PUMP TO COMPLETELY COOL BEFORE ATTEMPTING TO OPEN OR

SERVICE THE PUMP.

4. CAREFULLY CHECK THE TEMPERATURES BEFORE OPENING ANY

COVERS, PLATES, OR PLUGS.

5. CLOSE THE SUCTION AND DISCHARGE VALVES.

6. CAREFULLY AND SLOWLY VENT THE PUMP.

7. DRAIN THE PUMP.

A. REMOVING THE SUCTION INLET ASSEMBLY & WEARPLATE

While being sure the suction inlet assembly is supported, take out the mounting

hardware, the suction inlet assembly and the suction inlet gasket.

There are two sets of 16mm taped holes in the front wearplate to facilitate its

removal (top, bottom and at 120° increments). The holes are not completely taped

so they must be used with a puller.

Examine the front wearplate and its gasket, and install new ones if they appear worn

or damaged.

Using feeler gauge, determine how much wear has taken place between the impeller

and wearplate. If more the 1/8

inch gap, the wear plate should be replaced (Figure

1).

Содержание 10-WSP









































































Результаты поиска

Содержание 10-WSP

Отзывы:

Trillium 10-WSP, Инструкция по установке, эксплуатации и обслуживанию, Страница: 18 / 72

Результаты поиска

Содержание 10-WSP

Отзывы: