Trillium 10-WSP Скачать руководство пользователя страница 53

Страница: 53 / 72

WSP™

DATA SHEET

WSP™ SELF-PRIMER PUMPS

WSP-D300_10

Rev. 3

01/09/20

ALIGNMENT ADJUSTMENT IN ONE DIRECTION MAY DISRUPT ALIGNMENT

ADJUSTMENT IN ANOTHER DIRECTION. CHECK EACH PROCEDURE AFTER

ALTERING ALIGNMENT.

1. Coupled Drives

The axis of the power source and the axis of the pump shaft

must

be aligned

in both the vertical and horizontal planes when using couplings. Consult the

coupling manufacturer’s service documentation for specific clearance or gap

requirements between the driven and driving shafts.

2. Spider Insert-type Couplings

Use calipers to measure dimensions on the circumference of the outer ends

of the coupling hub every 90º when aligning spider insert-type couplings. The

coupling is only in perfect alignment when hub ends are spaced evenly at all

points (Figure 19).

Figure 19

3. Non-Spider Type Couplings

Use a feeler or taper gauge between coupling halves every 90º to align non-

spider type couplings. The coupling is only in perfect alignment when hubs

are equidistant to each other at every point. (Refer to manufacturers

instructions).

Ensure the coupling adjustment is parallel by laying a straightedge across the

top of both coupling rims, along the side and the bottom. The coupling is in

an accurate horizontal parallel alignment when the straightedge lies evenly

on both halves of the coupling.

Содержание 10-WSP









































































Результаты поиска

Содержание 10-WSP

Отзывы:

Trillium 10-WSP, Инструкция по установке, эксплуатации и обслуживанию, Страница: 53 / 72

Результаты поиска

Содержание 10-WSP

Отзывы: