Trillium 10-WSP Скачать руководство пользователя страница 10

Страница: 10 / 72

WSP™

DATA SHEET

WSP™ SELF-PRIMER PUMPS

WSP-D300_10

Rev. 3

01/09/20

7. DRAIN THE PUMP.

PUMP LIFTING EYES ON THE SELF-PRIMING PUMP ARE ONLY DESIGNED TO

HANDLE THE WEIGHT OF THE BARE PUMP. BEFORE LIFTING, ENSURE

THAT ALL SUCTION AND DISCHARGE HOSES AND PIPING HAVE BEEN

REMOVED FROM THE PUMP, AND IT IS FREE OF ANY BASE AND DRIVER.

EQUIPMENT LIFTING DEVICES SUCH AS CHAIN, LIFTING EYES, HOOKS, ETC.,

MUST BE APPROVED BY LOCAL, STATE, OR FEDERAL SAFETY CODES.

HOIST AND CRANES MUST BE ADEQUATELY SIZED TO LIFT RATED LOADS.

FAILURE TO USE APPROVED LIFTING DEVICES MAY RESULT IN INJURY.

BEFORE USING ANY CLEANING SOLVENTS CAREFULLY READ AND FOLLOW ALL

PRECAUTIONS PRINTED ON THE SOLVENT CONTAINER. CLEANING SOLVENTS ARE

KNOWN TO BE TOXIC AND FLAMMABLE AND ARE ONLY TO BE USED IN WELL-

VENTILATED AREAS AWAY FROM EXCESSIVE HEAT, SPARKS, AND FLAMES.

PRESSURE WITHIN THE PUMP MAY CAUSE PARTS TO BECOME DISENGAGED

AND EXPELED VIOLENTLY, CAUSING POTENTIAL SEVERE INJURY TO

PERSONNEL. ALWAYS ALLOW THE PUMP TO COOL BEFORE SERVICING.

THIS PUMP SHOULD ONLY BE OPERATED IN THE DIRECTION SHOWN ON THE

ARROW ON THE PUMP BODY AND ON ANY ACCOMPANYING DECALS.

Содержание 10-WSP









































































Результаты поиска

Содержание 10-WSP

Отзывы:

Trillium 10-WSP, Инструкция по установке, эксплуатации и обслуживанию, Страница: 10 / 72

Результаты поиска

Содержание 10-WSP

Отзывы: