Trillium 10-WSP Скачать руководство пользователя страница 5

Страница: 5 / 72

WSP™

DATA SHEET

WSP™ SELF-PRIMER PUMPS

WSP-D300_10

Rev. 3

01/09/20

IMMEDIATE HAZARDS WHICH WILL RESULT

IN SEVERE PERSONAL INJURY OR DEATH.

THESE INSTRUCTIONS DESCRIBE THE

PROCEDURE REQUIRED AND THE INJURY

WHICH WILL RESULT FROM FAILURE TO

FOLLOW THE PROCEDURE.

HAZARDS OR UNSAFE PRACTICES WHICH

COULD RESULT IN SEVERE PERSONAL

INJURY OR DEATH. THESE INSTRUCTIONS

DESCRIBE THE PROCEDURE REQUIRED

AND THE INJURY WHICH COULD RESULT

FROM FAILURE TO FOLLOW THE

PROCEDURE.

HAZARDS OR UNSAFE PRACTICES WHICH

COULD RESULT IN MINOR PERSONAL

INJURY OR PRODUCT OR PROPERTY

DAMAGE WHICH COULD RESULT FROM

FAILURE TO FOLLOW THE PROCEDURE.

II. SAFETY

The installation, operation and maintenance warnings for all sized WSP™ Self-

Primer (WSP) Pumps follows:

PLEASE STUDY THESE INSTRUCTIONS CAREFULLY BEFORE PUTTING THE

PUMP INTO SERVICE. ADHERENCE TO THESE INSTRUCTIONS IS NECESSARY

TO ENSURE THAT OPERATOR SAFETY AND SATISFACTORY PUMP OPERATION

ARE NEVER COMPROMISED. OPERATING PERSONNEL MUST READ AND

UNDERSTAND THESE INSTRUCTIONS BEFORE ANY ATTEMPT TO SERVICE THE

PUMP IS MADE.

Содержание 10-WSP









































































Результаты поиска

Содержание 10-WSP

Отзывы:

Trillium 10-WSP, Инструкция по установке, эксплуатации и обслуживанию, Страница: 5 / 72

Результаты поиска

Содержание 10-WSP

Отзывы: