Trillium 10-WSP Скачать руководство пользователя страница 13

Страница: 13 / 72

WSP™

DATA SHEET

WSP™ SELF-PRIMER PUMPS

WSP-D300_10

Rev. 3

01/09/20

ANY TIME THE OLD SEAL IS REMOVED FROM THE PUMP A NEW SEAL ASSEMBLY

SHOULD BE INSTALLED. DURING REASSEMBLY WEAR PATTERNS ON THE

FINISHED FACES CANNOT BE REALIGNED. PREMATURE SEAL FAILURE WILL

RESULT FROM USING AN OLD SEAL.

OPERATION AT TEMPERATURES ABOVE 160

F (71

C). IS NOT RECOMMENDED FOR

THIS SEAL. THIS PUMP SHOULD NOT BE USED AT HIGHER OPERATING

TEMPERATURES, WITHOUT CONSULTING THE FACTORY.

WHEN REUSING AN OLD SEAL, DO NOT ATTEMPT TO SEPARATE THE

ROTATING PORTION OF THE SEAL FROM THE SHAFT SLEEVE. DURING USE

THE RUBBER BELLOWS WILL BOND TO THE SLEEVE AND ATTEMPTING TO

SEPARATE THEM WILL DAMAGE THE BELLOWS.

BEFORE REINSTALLING THE IMPELLER, COMPLETELY CLEAN THE SHAFT AND

IMPELLER THREADS. THE SMALLEST AMOUNT OF DIRT ON THE THREADS COULD

CAUSE THE IMPELLER TO SEIZE ON THE SHAFT, WHICH, IN TURN, MAKES FUTURE

REMOVAL DIFFICULT IF NOT IMPOSSIBLE WITHOUT SHAFT AND IMPELLER

DAMAGE.

INSTALLATION AND OPERATION OF THE PUMPS AND ASSOCIATED EQUIPMENT

MUST BE IN ACCORDANCE WITH ALL NATIONAL AND LOCAL CODES, AS WELL AS

INDUSTRY STANDARDS.

Содержание 10-WSP









































































Результаты поиска

Содержание 10-WSP

Отзывы:

Trillium 10-WSP, Инструкция по установке, эксплуатации и обслуживанию, Страница: 13 / 72

Результаты поиска

Содержание 10-WSP

Отзывы: