Trillium 10-WSP Скачать руководство пользователя страница 40

Страница: 40 / 72

WSP™

DATA SHEET

WSP™ SELF-PRIMER PUMPS

WSP-D300_10

Rev. 3

01/09/20

VIII. INSTALLATION

Carefully review all previous warnings before attempting to install your WSP™

Self-Primer (WSP) Pump. This will maximize safety for both equipment and

operator.

Weir Specialty Pumps requires the general recommendations and practices that

follow are used when inspecting, positioning and arranging both the pump and

the attached piping. A majority of the information is applicable to standard, static

lift applications. In these applications, the pump is located above the level of

liquid or slurry to be pumped.

When the WSP™ Self-Primer (WSP) Pump is installed in a flooded suction

application, the liquid or slurry entering the pump is being forced in under

pressure. For each individual application, information on the mounting, line

configuration and priming needs to be adapted to ensure maximum performance.

and pump efficiency Be aware the pressure supplied to each pump is critical to

equipment performance and operator safety; so be careful to limit the pump

pressure to no more than 50% of the maximum operating pressure allowed. This

information is located in the Pump Performance Curve graph located in Section X

of this instruction manual.

Please contact your local WSP™ distributor or the factory if you need additional

help.

A. PUMP DIMENSIONS

For the physical dimensions of your WSP™ Self-Primer (WSP) Pump, see

Section X of this instruction manual.

B. INSPECTION PRIOR TO INSTALLATION

To ensure satisfaction and peak performance, your WSP™ pump assembly

received a thorough inspection and testing before being shipped from the

factory. Re-inspect the pump for any shipment damage before installing.

The following checklist will assist you in your preliminary inspection:

1. Are there cracks, dents, damaged threads and any other visible

damage to the pump?

2. Is there any loose hardware at the mating surfaces from gaskets that

may have shrunk? Is there any other loose attaching hardware that

needs to be tightened?

3. Have you followed all steps noted in the warnings in this manual or

those affixed to the pumps?

Содержание 10-WSP









































































Результаты поиска

Содержание 10-WSP

Отзывы:

Trillium 10-WSP, Инструкция по установке, эксплуатации и обслуживанию, Страница: 40 / 72

Результаты поиска

Содержание 10-WSP

Отзывы: