TPG CA-203A, Руководство по эксплуатации

Страница: 16 / 109

Chapter 5 Function parameter
26
12. d0.11
Panel potentiometer
voltage Panel potentiometer setting
voltage value
0.01V ●
13. d0.12 Motor actual speed Motor actual running speed 1rpm ●
14. d0.13 PID setting value
Setting value percentage under
PID adjustment mode
1% ●
15. d0.14 PID feedback value
Feedback value percentage under
PID adjustment mode
1% ●
16. d0.15
Current stage of
multi-speed
Current stage of multi-speed - ●
17. d0.16 Reserved
18. d0.17
Inverter module
temperature
0 to 100.0 ℃ 0.1
℃
●
19. d0.18 Software version DSP software version number - ●
20. d0.19 Cumulative running
time of this unit
0 to 65535h 1h ●
21. d0.20 Torque setting value
Observe the set command torque
under speed mode or torque
control mode
0.1% ●
5-1-2.F0 Group - Basic function
No. Code
Parameter
name
Setting range
Factory
default
Change
22. F0.00 Control mode
0: Open-loop flux vector control
1: Reserved
2: V/F control
3: torque control
2 ★
23. F0.01 Keyboard set
frequency
0.00Hz to F0.08 (maximum output
frequency)
50.00Hz
☆
24. F0.02
Frequency
command
selection
0: keyboard setting
1: Analog AI1 setting
2: Analog AI2 setting
3: Panel potentiometer setting
4: AI1+ AI2 setting
5: Multi-speed operation setting
6: PID control setting
7: Remote communications setting
0
★
25. F0.03
Keyboard and
terminal
UP/DOWN
setting 0: Valid, and the inverter power
failure with data storage
1: Valid, and the inverter power
failure without data storage
0 ☆
Chapter 5 Function parameter
27
2: UP/DOWN setting is invalid
3: Valid when running, invalid
when stop
26. F0.04
Command source
channel
0: Keyboard command channel
1: Terminal command channel
2: Communication command
channel
0
★
27. F0.05
Acceleration
time 1
0.1 to 3600.0s
Depends
on models
☆
28. F0.06
Deceleration
time 1
0.1 to 3600.0s
Depends
on models
☆
29. F0.07
Carrier frequency
setting
1.0 to 15.0kHz
Depends
on models
☆
30. F0.08
Maximum output
frequency
10.00 to 400.00Hz 50.00Hz
★
31. F0.09
Upper limit
frequency setting
source selection
0: Keyboard setting (F0.10)
1: Analog AI1 setting
2: Analog AI2 setting
3: Multi-speed setting
4: Remote communications setting
Note: Option 1 to 4, the setting
value 100% corresponds to the
maximum output frequency
0
★
32. F0.10
Running
frequency upper
limit
F0.11 to F0.08 (maximum output
frequency)
50.00Hz
☆
33. F0.11
Running
frequency lower
limit
0.00Hz to F0.10 (running
frequency upper limit)
0.00Hz
☆
34. F0.12
Running
direction
selection 0: default
1: opposite
2: reverse prohibited
0 ★
35. F0.13
AVR function
selection
0: Invalid
1: full valid
2: only invalid during deceleration
1
☆
5-1-3.F1 Group - Input terminals
No. Code Parameter name Setting range
Factory
default
Change
36. F1.00
DI1 terminal
function selection 0: No function
1: Forward run
1 ★