TPG CA-203A, Руководство по эксплуатации

Страница: 35 / 109

Chapter 5 Function parameter
64
BIT1: Bus voltage
BIT2: Input terminal status
BIT3: Output terminal status
BIT4: PID setting value
BIT5: PID feedback value
BIT6: Analog AI1 value
BIT7: Analog AI2 value
BIT8: Current stage of multi-
speed
BIT9: Torque set value.
BIT10 to BIT15: Reserved
The setting on this function is same with F6.01 setting. When CA SERIES inverter
stops, the parameters display is effected by this function code.
F6.03
Speed display
coefficient
0.1 to 999.9%
Mechanical speed = 120 *
running frequency *
F6.03/number of motor pole
pairs.
100.0%
☆
Mechanical speed =120* operating frequency of *F6.03/ motor, the function code
is used to correct the speed calibration display error, no impact on the actual speed.
F6.04 to
F6.07
Reserved
5-2-9.F7 Group - Auxiliary function group
Code Parameter name Setting range
Factory
default
Change
F7.00 Jog running frequency
0.00 to F0.08 (maximum output
frequency)
5.00Hz ☆
F7.01
Jog running
acceleration time
0.1 to 3600.0s
Depends on
models
☆
F7.02
Jog running
deceleration time
0.1 to 3600.0s
Depends on
models
☆
Defined the inverter's setting frequency and ac/deceleration time when jogging
Jog running start mode: direct start-up, and jog running stop mode: deceleration stop
(F3.05 = 0) .
Jog running acceleration time refers to the time required that the inverter
accelerates from 0Hz to maximum output frequency (F0.08) ;
Jog running deceleration time refers to the time required that the inverter
decelerates from maximum output frequency (F0.08) to 0Hz.
F7.03 Acceleration time 2 0.1 to 3600.0s
Depends on
models
☆
F7.04 Deceleration time 2 0.1 to 3600.0s
Depends on
models
☆
Chapter 5 Function parameter
65
CA SERIES provides two sets of acceleration and deceleration time. Their
meanings are the same, please refer to the instructions on F0.05 and F0.06.
Use multi-function digital input terminal DI to set, switch between ac/deceleration
1 and ac/deceleration time 2. For the detailed method, please refer to the instructions on
function codes F1.00 to F1.05.
F7.05 Jump frequency
0.00 to F0.08 (maximum output
frequency)
0.00Hz ☆
F7.06 Jump frequency range
0.00 to F0.08 (maximum output
frequency)
0.00Hz ☆
When the set frequency is within the jump frequency range, the actual running
frequency will be the boundaries of the jump frequency.
The inverter can avoid mechanical resonance point of load by setting jump
frequency. This inverter can set 1 jump frequency point. If the jump frequency points
are set to 0, this function does not work.
1/ 2*
跳跃幅度
1/ 2*
跳跃幅度
时间（
t
）
设定频率（
f
）
跳跃频率
跳跃频率示意图
Invalid 0
F7.07
Jump frequency
availability during
ac/deceleration process Valid
1
0 ☆
The function code is used to set whether the jump frequency is active or not in the
process of acceleration and deceleration.
If it is set to active, when the operating frequency is in the jump frequency range,
the actual operating frequency will skip the set jump frequency boundary.
1/2*
跳跃幅度
1/2*
跳跃幅度
时间（
t
）
设定频率（
f
）
跳跃频率
加减速过程中跳跃频率有效示意图
Set frequency (f)
Jump
frequency
1/2* Jump amplitude
1/2* Jump amplitude
Time(t)
Schematic diagram of jump frequency valid in the process of acceleration.
Time(t)
Schematic diagram of jump frequency
Set frequency (f)
1/2* Jump amplitude
1/2* Jump amplitude
Jump
frequency