Toshiba Strata CTX, Руководство по программированию, Страница: 338 / 533

Telephone Button Programming
300 Series Programs
13-60
Strata CTX Programming - Part 3:Telephone Button Programming 04/03
309-15 VM Dial
)%
, n,
+ROG
,
+ROG
n = Digits 0~9, * and #. For a
pause enter Px, where
x=0~9 (seconds), up to 10
characters (default = no
value). Enter the VM mail box number which should answer calls for this DID/
DNIS number.
This mail box number will be sent to voice mail on a DID/DNIS call
that rings directly to voice mail; and, on a direct DID/DNIS call to a DN
that forwards to voice mail before it is answered by the DN.
If a DID/DNIS call is answered by a station and then transferred to a
DN that forwards to voice mail, this mail box number of the DID/DNIS
number or the forwarding DN’s mail box number will be sent to voice
mail per Program 579, 01.
If this VMID code is not set, direct DID/DNIS calls will go to the VM
general greeting and DID/DNIS calls that forward from a DN to VM
will go to the DN’s VMID mail box. This voice mail box number is sent
to the VM port, as DTMF digits, after the VM port answers a DID/
DNIS call as explained above. These digits are sent to the VM port if
the CTX is set for SMDI or DTMF integration in Program 580, 01.
310 DIT Assignment
,
+ROG
This command assigns DIT Number Analysis Table for DIT trunks.
DIT trunks are ground and loop start trunks.
310-00 Line Equipment No.
xxyyzz,
+ROG
xx = Cabinet 1 (CTX100),
01~02 (CTX670 Basic),
01~07 (CTX670 Exp.) Enter the trunk equipment number. Equipment numbers are required
when assigning a new trunk to the system. It can also be used to
display the equipment location of existing trunks.
Example: If a line should be assigned to an RCOU in cabinet shelf 5,
slot 2, circuit 3, enter 050203.
Cabinet numbers:
•
CTX100 – Select 01 for Base and Expansion cabinet.
•
CTX670 – Select 01 for Base and 02~07 respectively for each
Expansion cabinet.
Slot numbers:
• CTX100 – Select 01~04 for Base slots and 05~08 for Expansion
slots.
•
CTX670 – Select 01~08 for Base slots and 01~10 for Expansion
slots.
yy = Slot 01~8 (CTX100),
01~10 (CTX670)
zz = Circuit 01~24
310-
01~03 Day1/Day2/Night
Destination Type
)%
~
)%
, n,
6SNU
n = 1. No Data (default)
2. Dialing Digits
3. DISA
4. Built-in Modem
5. Night Bell
Select Destination Type for each.
• No Data – no destination will ring when the line rings into the
system.
•
Dialing Digits – assigns the line to ring the directory number or
access code defined in the “Destination Digits” assignment
•
DISA – assigns the line to ring in as a DISA call. DISA dial tone
will be returned to the caller.
•
Modem – assigns the line to ring the remote maintenance modem
on the CTX processor. Used to call into the system with a CTX
WinAdmin PC and modem.
• Night Bell – Assigns the line to cause the night relay to pulse
(one-sec. close/3-sec. open)
Day1/Day2/Night
Destination Digits
n1,
+ROG
n1 = Up to 32 digits Enter Destination, Directory Number or Access Codes for each, only
if Dialing Digits is selected as Destination Type.
•
If Dialing Digits is the Destination Type, enter the Directory
Number that the line should ring.If the line should ring over
external page, enter #31xx, where xx is the external Page group
number.
• If the default page access code #31 was changed, use the new
page access code as the leading digits.
•
Line access codes and network routing numbers can also be
entered to route incoming calls back out to a public or private
network number.
Programs 303~315
(continued)
Button Sequence Value(s) Summary