Toshiba Estia RUA-CP1701H Скачать руководство пользователя страница 81

Страница: 81 / 94

Monobloc Outdoor Unit Installation Manual

CAUTION:

•

Commissioning and start-up of the heat pump must be supervised by a qualified refrigeration qualified

technician.

•

Start-up and operating tests must be carried out with a thermal load applied and water circulating in the

water heat exchanger.

•

All set point adjustments and control tests must be carried out before the unit is started up.

Ensure that all safety devices are operational, especially that the high pressure switches are functioning on and

that any alarms are acknowledged.

Note:

If the Manufacturer instructions (power and water connections and installation) are not observed, the

Manufacturer warranty becomes invalid.

System Start Up:

Start the system in heating mode. Check the following parameters during the test and ensure that no error codes

are generated during the start-up test.

Date / Hour

Air

Outdoor Air Temp (°C)

P001

Water

Entering Water Temp (°C)

P003

Leaving Water Temp (°C)

P004

Water Control Temp (°C)

P052

Suction

Saturated Suction Temp (°C)

P008

Suction Temperature (°C)

P009

Superheat Temperature (°C)

P015

Superheat Target Temp (°C)

P016

Discharge

Discharge Temperature (°C)

P010

Refrigerant Temperature (°C)

P005

Compressor

Requested Compressor Frequency (Hz)

P022

Actual Compressor Frequency (Hz)

P023

Water control

Water Control Point (°C)

P051

Flow Switch Status

P105

Safety Switch Status

P104

Water

pressure /

flow rate

Entering water heat exchanger pressure (kPa)

Leaving water heat exchanger pressure (kPa)

Pressure drop (without internal pump)(kPa)

Flow rate from curves (without internal pump) (l/sec)

Or available external pressure (with internal pump) (kPa)

Flow rate from curves (with internal pump) (l/sec)

Power

Network Voltage (V)

Input Amperage (A)

Repeat the above test with the heat pump system operating in cooling mode and DHW mode.

Содержание Estia RUA-CP1701H































































































Результаты поиска

Содержание Estia RUA-CP1701H

Отзывы:

Похожие инструкции для Estia RUA-CP1701H

Бренды по названию

Популярные бренды

Toshiba Estia RUA-CP1701H, Руководство по установке

Результаты поиска

Содержание Estia RUA-CP1701H

Отзывы:

Похожие инструкции для Estia RUA-CP1701H

Бренды по названию

Популярные бренды