Toshiba Estia RUA-CP1701H Скачать руководство пользователя страница 39

Страница: 39 / 94

Monobloc Outdoor Unit Installation Manual

For 24-hour format:

Set the hour and press the

Schedule

key to confirm. Then, set minutes and press the

Schedule

key to confirm.

To confirm all changes, press and hold the Schedule key for 2 seconds.

8.1.2 Second step of configuration: Parameter menu

According to the application of unit, several parameters are to be configured to allow the correct operation

of system. The following sections explain some standard cases of installation. But to configure the unit, it is

necessary to access the parameter menu. If there is no user interface on the unit, it is necessary to use Customer

communication bus (Proprietary Protocol or Jbus) to configure the unit. Otherwise in the case with user interface,

follow the next procedure.

To access the parameter menu

If the user interface is in standby mode, press one key to activate the remote controller screen. Press and hold the

Occupancy

key and the

Schedule

key simultaneously for 2 seconds.

The password screen is displayed:

Enter the password:

0120

. To change the number, press the

Down

key.

To validate each number, press the

Schedule

key.

Содержание Estia RUA-CP1701H































































































Результаты поиска

Содержание Estia RUA-CP1701H

Отзывы:

Похожие инструкции для Estia RUA-CP1701H

Бренды по названию

Популярные бренды

Toshiba Estia RUA-CP1701H, Руководство по установке

Результаты поиска

Содержание Estia RUA-CP1701H

Отзывы:

Похожие инструкции для Estia RUA-CP1701H

Бренды по названию

Популярные бренды